Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Eaton Viking 40A75E1 - a large Viking from Canadian forests
#14

Pete;
  There was an older version of a 6SF5 called a 6F5, but it has a grid cap, and the pinout is different, a 6J5 is similar again but I think that the trans conductance is different, why Electrohome chose to use two different single ended triode tubes right next to each other, only they could answer. A lot of sets used a 6F5 or a 6K5 along with a 6H6 to perform the same job as a 6Q7 or 6R7 would in another set, but it looks like D.E chose to wire up a triode as a diode in your set.
  Yes, they call those small batteries bias cells, Electrohome must have had a liking for them in the 1940-41 model year as the Phonola console I have also has a pair of them. I wonder if they may have hired on some engineers from Rogers or Canadian Marconi as those companies were infamous for the use of bias cells, from about 1936-37 up until the war? I think that it must have been some sort of patent royalty avoidance scheme, possibly to RCA or Hazeltine Research, as all three of those companies used cathode bias/self bias, or fixed bias via the power supply, for their tubes before adopting those silly bias cells.
  The company that developed and market these was P.R Mallory, a battery and radio parts manufacturer, the cells are carbon zinc and put out about 1.4 volts, at almost no current, there were various advantages they cited in their marketing but I think that they were tenuous at best, the only one I could understand is that it's a source of grid bias with zero AC ripple. In many cases you can rewire the tube to self bias, but modern watch batteries are not difficult, nor expensive to buy, though the polarity is opposite that of the old bias cells.
Regards
Arran


Messages In This Thread
RE: Eaton Viking 40A75E1 - a large Viking from Canadian forests - by Arran - 01-11-2019, 12:03 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM
Philco 46-480 Electronic Restoration
Nope, he can’t tell me the dimensions. Looks like I won’t be buying it.jrblasde — 02:38 PM
Philco 46-480 Electronic Restoration
Hello Joseph , It sounds like you found a good seller and yes shipping is really expensive ! Sincerely Richardradiorich — 02:16 PM

[-]
Who's Online
There are currently 2573 online users. [Complete List]
» 5 Member(s) | 2568 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>