1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Adding phono input to a 37-650X
islesailor
Junior Member
**
Posts: 3
Threads: 1
Joined: May 2019
City: Fort Pierce State, Province, Country: Florida
#2

05-20-2019, 08:46 PM
I added a jack for a bluetooth reciever to my 37-650x, it works fine. Should work for your phono. Mount a jack aand a spdt on the rear of your chassis. Since the radio is mono you need to combine the stereo channels. Connect a 1K resistor to each side of the jack. Connect the 1K resistors together and to a 1 Meg resistor. Connect the 1 Meg to ground. Connect the junction of the 2 1K and the 1 Meg to one side of the SPDT switch. Disconnect C33 (.01) from the junction of R31/R32. Connect C33 to the center terminal of the switch. Connect the other side of the switch to the place where you disconnected C33. Connect the third pin on the jack to ground.
Enjoy
Kelton
W4IND
(This post was last modified: 05-21-2019, 12:56 PM by islesailor.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Adding phono input to a 37-650X - by islesailor - 05-20-2019, 08:46 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Atwater-Kent 84, restoration.
Hello Mike, Wow ! far as my AK it does work and the cabinet is in nice shape so is my chassis anyway here is a photo of...radiorich — 02:59 AM
Atwater-Kent 84, restoration.
Nice radio, Mike! Here's hoping it was well rebuilt. Take care and BE HEALTHY! GaryGarySP — 12:12 AM
Atwater-Kent 84, restoration.
Rich yes, this is the way I got it. I have just put it on the table and took it apart. I suspect it even might work,...morzh — 11:31 PM
Atwater-Kent 84, restoration.
Hello mike, What nice looking radio I have one AK in my collection it's a console I have not started restoring it yet ....radiorich — 11:21 PM
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration