1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Radio City Products Signal Generator Model 705A
captainclock1988
Senior Member
****
Posts: 322
Threads: 34
Joined: Dec 2019
City: Elkhart State, Province, Country: Indiana
#4

05-03-2020, 11:22 PM
Ok so from what I've seen of pictures of the RCP Model 705A Signal Generator, it seems that the original RF Output plug was basically just a hot lead all by itself and then the ground lead was independent of it and hooked up to the banana plug jack that's marked "GND" next to the AF Output jack.
So it seems that all I need is some RG-58 Coaxial cable that I could wire one side to my already existing mic plug and then the other side wire up to an insulated red colored alligator clip, and then have a regular black banana plug wired to a 4' length of black wire on one end and the other end a black insulated alligator clip attached for the ground lead. 

Here's the picture I found posted below showing the original RF-Output test lead.

   
(This post was last modified: 05-03-2020, 11:25 PM by captainclock1988.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Radio City Products Signal Generator Model 705A - by captainclock1988 - 05-03-2020, 11:22 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM
Var resistor id
Its a Sylvania 400 oscilloscope. here is a clip of r-100. Would be nice to know the current required. Not listed in part...Martinj — 02:10 PM
The list of my radio & TV collection!
Thanks Richard. I hope you enjoy it. Here I have created an English section on the history of radio with videos in Engl...RadioSvit — 10:23 AM
The list of my radio & TV collection!
Hello RadioSvit, first all happy new year ! I will watch your new videos this week. Sincerely Richardradiorich — 09:19 AM

[-]
Who's Online
There are currently 9564 online users. [Complete List]
» 2 Member(s) | 9562 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment