1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Noise in 680X and 37-690
AI2V
Member
***
Posts: 201
Threads: 26
Joined: Dec 2005
City: Morris Plains, NJ
#7

04-15-2006, 09:27 AM
Don't go completely nuts in hunting down bad resistors until you have swapped out your output amplifier tubes with known good ones. 42's are notorious for intermittent frying bacon sounds- I've got a box of noisy ones. Noisy 42's can sometimes be used in the audio driver stage, but never in the final stage.
Pete AI2V
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Noise in 680X and 37-690 - by Fred R - 12-28-2005, 10:23 PM
RE: Noise in 680X and 37-690 - by Sam samuelian - 05-22-2012, 05:42 AM
RE: Noise in 680X and 37-690 - by Arran - 05-22-2012, 06:51 PM
RE: Noise in 680X and 37-690 - by Ron Ramirez - 05-22-2012, 07:01 PM
RE: Noise in 680X and 37-690 - by Sam samuelian - 05-22-2012, 10:25 PM
RE: Noise in 680X and 37-690 - by morzh - 05-23-2012, 10:06 AM
RE: Noise in 680X and 37-690 - by Ron Ramirez - 12-30-2005, 12:37 AM
[No subject] - by Fred R - 12-30-2005, 10:41 AM
[No subject] - by Ron Ramirez - 12-30-2005, 11:30 AM
[No subject] - by Chuck Schwark - 12-30-2005, 12:00 PM
[No subject] - by Frank - 04-13-2006, 10:17 AM
Noise in output - by AI2V - 04-15-2006, 09:27 AM
[No subject] - by Ron Ramirez - 04-16-2006, 10:06 PM
[No subject] - by Frank - 04-19-2006, 09:03 AM
[No subject] - by Frank - 04-24-2006, 08:55 AM
[No subject] - by Frank - 04-25-2006, 08:41 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration