Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 16X restoration
#34

I thought I did not have 78 tubes.
Also I realized one of the 78 tubes was replaced with a 77 one.
When I damaged one 78 in the beginning, I thought I did not have any in stock and now I even thought of buying some. Then I looked at my bench plastic bins, and I have a whole bin-full of them.
So I picked three that tested like new.

Also on the photo you could see a 77 tube's (the one right under the two IF cans) grid wire is outside the shell; I am sure it should be inside.

So I put all the tubes in, made sure it started rectifying at about 50VAC, and then went to 110VAC.
There was hum in the speaker and it reacted to the volume pot wiper being touched.
I could hear aerial noise, but rotating the tuning cap at where the local station is did not result in reception, so I will have to look at the RF circuit.
But so far no smoke and AF working is a good sign.


PS. Of course it works. I came down to see why there is no reception and then it occur to me to check the band switch posiition. Sur'nuff, it was on some SW band. Put in the BC position, the radio clearly receives the local station.

PPS. Putting the heat shield to the wire-wound resistor in the back proved to be a bit of a challenge. When taking that off I did not feel like taking the resistor out, so I bent a side. Putting it back was not possible without taking the resistor out, so I straightened the bent side, took the resistor out and then the insulating washer that is in between the holder and the resistor's end (probably to stress-relieve the ceramic) disintegrated, having been burnt over the years. And I do not have a fibre washer in the house. So I searched far and wide and found a fibre bushing which was exactly the right size and the internal diameter, so I saw off a piece to make a washer, and then spent some 15 minutes hand-sanding it to the right thickness. Eventually it went in. So the under-chassis is done.

I turned the speaker towards myself when playing (the cone facing the bench top obviously affects the sound) and was pleasantly surprise by a good clean base.

Now to alignment.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 16X restoration - by morzh - 10-02-2021, 06:15 PM
RE: Philco 16X restoration - by Radioroslyn - 10-02-2021, 10:48 PM
RE: Philco 16X restoration - by morzh - 10-02-2021, 10:59 PM
RE: Philco 16X restoration - by Ron Ramirez - 10-02-2021, 11:26 PM
RE: Philco 16X restoration - by Radioroslyn - 10-03-2021, 07:22 AM
RE: Philco 16X restoration - by morzh - 10-04-2021, 02:48 PM
RE: Philco 16X restoration - by morzh - 10-10-2021, 07:11 PM
RE: Philco 16X restoration - by RodB - 10-11-2021, 09:25 AM
RE: Philco 16X restoration - by Ron Ramirez - 10-11-2021, 09:32 AM
RE: Philco 16X restoration - by Ron Ramirez - 10-12-2021, 06:58 PM
RE: Philco 16X restoration - by mikethedruid - 10-13-2021, 12:02 AM
RE: Philco 16X restoration - by morzh - 10-19-2021, 06:16 PM
RE: Philco 16X restoration - by morzh - 10-25-2021, 10:15 PM
RE: Philco 16X restoration - by Ron Ramirez - 10-26-2021, 06:18 AM
RE: Philco 16X restoration - by morzh - 10-26-2021, 01:06 PM
RE: Philco 16X restoration - by morzh - 10-30-2021, 10:49 PM
RE: Philco 16X restoration - by morzh - 10-31-2021, 04:42 PM
RE: Philco 16X restoration - by morzh - 10-31-2021, 04:52 PM
RE: Philco 16X restoration - by David - 11-01-2021, 09:23 AM
RE: Philco 16X restoration - by morzh - 11-06-2021, 07:20 PM
RE: Philco 16X restoration - by Brad Winder - 11-06-2021, 08:45 PM
RE: Philco 16X restoration - by morzh - 11-06-2021, 09:51 PM
RE: Philco 16X restoration - by morzh - 11-12-2021, 09:05 PM
RE: Philco 16X restoration - by morzh - 11-14-2021, 03:23 PM
RE: Philco 16X restoration - by morzh - 11-17-2021, 12:00 AM
RE: Philco 16X restoration - by morzh - 11-18-2021, 12:31 AM
RE: Philco 16X restoration - by morzh - 11-21-2021, 11:00 PM
RE: Philco 16X restoration - by Brad Winder - 11-22-2021, 12:39 AM
RE: Philco 16X restoration - by mikethedruid - 11-22-2021, 05:29 AM
RE: Philco 16X restoration - by Ron Ramirez - 11-22-2021, 09:13 AM
RE: Philco 16X restoration - by morzh - 11-22-2021, 12:39 PM
RE: Philco 16X restoration - by morzh - 11-22-2021, 10:57 PM
RE: Philco 16X restoration - by morzh - 11-26-2021, 11:46 PM
RE: Philco 16X restoration - by morzh - 11-27-2021, 05:07 PM
RE: Philco 16X restoration - by morzh - 11-28-2021, 09:30 PM
RE: Philco 16X restoration - by Simon Wa3uay - 11-29-2021, 01:24 PM
RE: Philco 16X restoration - by morzh - 11-29-2021, 02:11 PM
RE: Philco 16X restoration - by morzh - 11-30-2021, 04:56 PM
RE: Philco 16X restoration - by morzh - 12-04-2021, 03:41 PM
RE: Philco 16X restoration - by morzh - 12-05-2021, 09:52 PM
RE: Philco 16X restoration - by morzh - 12-08-2021, 09:30 PM
RE: Philco 16X restoration - by morzh - 12-09-2021, 08:05 PM
RE: Philco 16X restoration - by morzh - 01-01-2022, 05:18 PM
RE: Philco 16X restoration - by Radioroslyn - 01-01-2022, 10:18 PM
RE: Philco 16X restoration - by morzh - 01-01-2022, 11:10 PM



Users browsing this thread: 13 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Hi Nick, Usually the dashed lines connected to components means the part is a substitute in the circuit for specific ...RodB — 09:42 AM
462ron
Mike when I got to the guy’s house to pick up the set, he gave me a tour of his home and garage. Wow, his living room co...462ron — 09:10 AM
91H Code 126 Restore
I'm pretty sure that the dotted line I circled in an earlier post signifies that it is applicable to the 226 model which...RealRider — 08:05 AM
Philco 49-1040
Hello bob, that underside looks like it is all original ! Sincerely Richardradiorich — 02:07 AM
Philco 49-1040
Oh yes, many bumblebees and loktal tubes. The cutout is for the speaker.  Here's a photo from a different set. Bob Andersen — 12:59 AM
Philco 49-1040
Bob; Looks like another "Bumble Bee" special, like my Brand Z T.O radios. Is that section they took out of ...Arran — 12:19 AM
Philco 49-1040
Hello Bob, You are like the home for lost tv's like how people bring pets home ! Sincerely Richardradiorich — 12:00 AM
Philco 49-1040
I thought I had an arrangement to restore this set for a customer but his wife said heck no.  Instead, he gave it to me....Bob Andersen — 10:29 PM
Philco 46-480 Electronic Restoration
I kept working on reassembly this week. I wasn’t able to solder for a few days while it was too cold (single digit low t...jrblasde — 09:27 PM
Atwater-Kent 84, restoration.
Well, powering it up would be too good to be true, and I had that feeling. Before I did, I decided to check the coils...morzh — 06:02 PM

[-]
Who's Online
There are currently 5519 online users. [Complete List]
» 2 Member(s) | 5517 Guest(s)
AvatarAvatar

>