Noise in 680X and 37-690

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Noise in 680X and 37-690

Frank
Junior Member

Posts: 29
Threads: 8
Joined: Oct 2005

#10

04-24-2006, 08:55 AM

Ok, I did some more tracing this weekend, and I think the Philco replacement candohm is causing the noise. When the noise occurs, the voltage at the top of the resistor rises, and at the other lug, the voltage decreses in sync with the noise. This is for the 3000 ohm section. So, I'm going to order some 25 watt resistors and install them in place of the 3000 ohm and 2240 ohm sections. This probably will fix the problem, but at the very least, remove one potential source of this noise.

Will post a follow up when done.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Noise in 680X and 37-690 - by Fred R - 12-28-2005, 10:23 PM

RE: Noise in 680X and 37-690 - by Sam samuelian - 05-22-2012, 05:42 AM

RE: Noise in 680X and 37-690 - by Arran - 05-22-2012, 06:51 PM

RE: Noise in 680X and 37-690 - by Ron Ramirez - 05-22-2012, 07:01 PM

RE: Noise in 680X and 37-690 - by Sam samuelian - 05-22-2012, 10:25 PM

RE: Noise in 680X and 37-690 - by morzh - 05-23-2012, 10:06 AM

RE: Noise in 680X and 37-690 - by Ron Ramirez - 12-30-2005, 12:37 AM

[No subject] - by Fred R - 12-30-2005, 10:41 AM

[No subject] - by Ron Ramirez - 12-30-2005, 11:30 AM

[No subject] - by Chuck Schwark - 12-30-2005, 12:00 PM

[No subject] - by Frank - 04-13-2006, 10:17 AM

Noise in output - by AI2V - 04-15-2006, 09:27 AM

[No subject] - by Ron Ramirez - 04-16-2006, 10:06 PM

[No subject] - by Frank - 04-19-2006, 09:03 AM

[No subject] - by Frank - 04-24-2006, 08:55 AM

[No subject] - by Frank - 04-25-2006, 08:41 AM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
The speaker table error?
G 10-1/2" 65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H 10-1/2" 77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth! I hope the final result is as much a quality sounding example! Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me