Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 odd noise/distortion
#17

I am not an expert in radio repair, and learned most of what little I know from all the folks here over the years. I do this as a casual hobby, so a lot of top end test equipment is not in my possession. Sure, a mutual conductance tester would be nice, but I picked up an old Triplett tube tester at a MARC event a few years back. I replaced caps and resistors in it, and installed a new NE-2 bulb. All in all, I spent maybe $60.00 total. For my purposes it is usually all I need. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
37-116 odd noise/distortion - by poulsbobill - 07-12-2022, 07:08 PM
RE: 37-116 odd noise/distortion - by RodB - 07-13-2022, 10:19 AM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-13-2022, 08:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-22-2022, 10:45 PM
RE: 37-116 odd noise/distortion - by klondike98 - 07-23-2022, 02:14 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-23-2022, 08:23 PM
RE: 37-116 odd noise/distortion - by morzh - 07-23-2022, 08:45 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-24-2022, 07:16 PM
RE: 37-116 odd noise/distortion - by morzh - 07-24-2022, 07:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 11:40 AM
RE: 37-116 odd noise/distortion - by morzh - 07-25-2022, 08:37 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 08:49 PM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-25-2022, 10:10 PM
RE: 37-116 odd noise/distortion - by morzh - 07-26-2022, 12:02 AM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-26-2022, 03:06 AM
RE: 37-116 odd noise/distortion - by GarySP - 07-26-2022, 09:09 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
Is the chassis in the parts set less rusty then the one you have been working on or about the same?Arran — 02:50 AM
Gloritone 27 Radio
Hi Dconant, Yeah, I think someone tried to combine the 2 functions.  I don't think it will work.  In the early 27 sch...MrFixr55 — 12:04 AM
Gloritone 27 Radio
Well, now you ask that question and there we are, the time travellers.morzh — 11:44 PM
Gloritone 27 Radio
That's OK, Morzh, I do that all the time. If we could catalogue the answers to questions that no one asked, when they d...MrFixr55 — 11:35 PM
Atwater-Kent 84, restoration.
Today the 10 Ohms resistors came (It might've meant in the sch it was 10 ohm total), and soldering them in improved thin...morzh — 09:33 PM
Gloritone 27 Radio
Oops, sorry. I've answered a question no one asked. :)morzh — 02:13 PM
Gloritone 27 Radio
To clear things up a bit. The Philco pot (33-5040) is single gang 3 terminals with AC switch. The picture shows how my p...dconant — 01:52 PM
Gloritone 27 Radio
The 20 pot has two sections: one is the Antenna attenuator, the other is the cathode bias one.morzh — 12:11 PM
Gloritone 27 Radio
Does the Philco pot have only 1 element (2 or 3 terminals) or is it ganged (5 or 6 terminals)? You state that one con...MrFixr55 — 11:52 AM
Gloritone 27 Radio
Yep. It is a light version of Philco 20. I guess it was soon after the 24 tube appeared on the market and everyone start...morzh — 11:04 AM

[-]
Who's Online
There are currently no members online.

>