1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
bass does not work on 42-380
gennet2
Junior Member
**
Posts: 26
Threads: 8
Joined: Jun 2011
#6

06-21-2011, 05:56 AM
Thanks for info Chuck. I didn't replace the bakelite caps only the paper ones. I have never tried to realign it. Is that in the schmatic pages under DIAL CALIBRATION NOTE B adjusting low frequency. NOTE C is adjust high frequency. Other than that I would be lost. The only other thing I have done is to tweek the three cans on top for maximum volume. but I did mark location of each before I turned them. It only took maybe an eigth of a turn to acheive this. Any suggestions or maybe I don't have enough knowledge to do this. I have a multimeter if that is what i need.
Bob
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
bass does not work on 42-380 - by gennet2 - 06-18-2011, 11:35 AM
Re: bass does not work on 42-380 - by gennet2 - 06-18-2011, 12:54 PM
Re: bass does not work on 42-380 - by exray - 06-18-2011, 04:42 PM
Re: bass does not work on 42-380 - by gennet2 - 06-19-2011, 05:36 AM
Re: bass does not work on 42-380 - by gennet2 - 06-21-2011, 05:56 AM
Re: bass does not work on 42-380 - by gennet2 - 06-21-2011, 06:18 AM
Re: bass does not work on 42-380 - by Raleigh - 06-24-2011, 12:31 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

[-]
Who's Online
There are currently 6290 online users. [Complete List]
» 1 Member(s) | 6289 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration