Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Midwest 88
#5

+1 on Morzh's comments. You have Phriends here. My only suggestion is to clean up the socket, especially of that stray strand. Heatshrinking the wire where it enters the transformer case, even if NOS is a best practice. there was this plastic centipede type stuff that they used to use on one of the instruments that I serviced that you could work around wires threaded through a sharp hole, even after the wiring was installed.

Re Facebook- Ms. Fixr has a t shirt that states "I hope your life is at least 1/4 as great as you claim it to be on Facebook".

RE HOAs, not for me! My house is small, has only 4 small strips of land around it, but it is ours and there is no jurisdiction smaller than a town that can tell us what to do to it or on it.

Dad was widowed for 3 years before he married again. He and his 2nd wife decided to sell the family house to my sister and her husband (Ms. Fixr and I could not afford it) and move into a retirement community (One member of household had the be 55 or older, and no one under 18 in household). Dad was disabled, on crutches and a scooter, and could not drive, and the garage was too small for both him (passenger) and wife (driver) to open the doors in the garage, so he put up a wooden handrail so he could walk from the garage, along the front walkway. to the front door. A few weeks later, a woman with a clipboard was in his yard. When he asked what she was doing, she informed him that she was from the HOA and that his wood handrail was a violation. The rail had to be brass, and, of course, she had the name of an "approved" contractor (a relative, no doubt). Unfortunately, this was before the Americans with Disabilities Act.

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55


Messages In This Thread
Midwest 88 - by bridkarl - 09-02-2023, 06:28 PM
RE: Midwest 88 - by morzh - 09-02-2023, 07:21 PM
RE: Midwest 88 - by bridkarl - 09-02-2023, 07:40 PM
RE: Midwest 88 - by morzh - 09-02-2023, 09:26 PM
RE: Midwest 88 - by MrFixr55 - 09-03-2023, 09:22 PM
RE: Midwest 88 - by bridkarl - 09-04-2023, 09:48 AM
RE: Midwest 88 - by Paul Philco322 - 09-04-2023, 11:10 AM
RE: Midwest 88 - by Chas - 09-04-2023, 12:17 PM
RE: Midwest 88 - by GarySP - 09-04-2023, 12:17 PM
RE: Midwest 88 - by Ron Ramirez - 09-04-2023, 12:26 PM
RE: Midwest 88 - by morzh - 09-04-2023, 02:30 PM
RE: Midwest 88 - by Arran - 09-04-2023, 03:16 PM
RE: Midwest 88 - by morzh - 09-04-2023, 06:12 PM
RE: Midwest 88 - by RodB - 09-05-2023, 09:19 AM
RE: Midwest 88 - by morzh - 09-05-2023, 10:57 AM
RE: Midwest 88 - by bridkarl - 09-05-2023, 07:19 PM
RE: Midwest 88 - by morzh - 09-05-2023, 08:15 PM
RE: Midwest 88 - by bridkarl - 09-05-2023, 08:50 PM
RE: Midwest 88 - by morzh - 09-06-2023, 04:23 PM
RE: Midwest 88 - by GarySP - 09-07-2023, 10:00 AM
RE: Midwest 88 - by morzh - 09-07-2023, 02:05 PM
RE: Midwest 88 - by Joe Rossi - 09-07-2023, 03:38 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM
B&K 1077B no video
Thanks Rich! I'll take a look and see what he has. I know there's more modern equipment to be had, but this one I know a...TV MAN — 09:11 PM
B&K 1077B no video
Hello Tim, Here is a link to restoration of one on Phil's old radios site ! Sincerely Richard bk1077bradiorich — 09:01 PM
6TPZ and 5TPO Radio Help
I'm a little befuddled on this one. Should X5 and X4 be tied together like this?  It looks like someone added this at so...R3Sons — 07:33 PM

[-]
Who's Online
There are currently no members online.

>