[split] Philco 7050

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

[split] Philco 7050

EDDIE_MUTANTE
Junior Member

Posts: 5
Threads: 2
Joined: Nov 2023
City: LA (CASTRILLON) LAGUNA State, Province, Country: Spain

11-05-2023, 09:41 AM

Hello Dale.

What I mean (sorry for my horrible English) is that somebody has tryed to use the 7050 for something else and almost all inside has gone.
I have read the instructions to "calibrate" the line and I have rebuild the 6X5GT circuit with one diode and the resistors involved on it. I put one amp meter in parallel with the 220ohm resistor (R107 in the schematic) and connect my varistor regulated at 115Vac (50Hz here). I have 30Vac at the anode and 394 micro amperes. What I'm trying to calculate is the range of the milliamperimeter that uses the the 7050. As the needle must on the center with the meter I think that I need a 1mA amp meter, but will be great that somebody could measure that on a working unit. I have read here that the resistance of that instrument is around 50 ohm, but that don't help me too much.

A greeting!

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

[split] Philco 7050 - by EDDIE_MUTANTE - 11-02-2023, 02:45 PM

RE: [split] Philco 7050 - by EDDIE_MUTANTE - 11-04-2023, 10:31 AM

RE: [split] Philco 7050 - by DaleHCook - 11-04-2023, 12:45 PM

RE: [split] Philco 7050 - by EDDIE_MUTANTE - 11-05-2023, 09:41 AM

RE: [split] Philco 7050 - by DaleHCook - 11-05-2023, 10:45 AM

RE: [split] Philco 7050 - by EDDIE_MUTANTE - 11-05-2023, 01:44 PM

RE: [split] Philco 7050 - by morzh - 11-05-2023, 04:23 PM

RE: [split] Philco 7050 - by klondike98 - 11-06-2023, 03:06 PM

RE: [split] Philco 7050 - by Soundwon - 12-08-2023, 11:42 PM

RE: Philco 7050 reading high - by morzh - 11-02-2023, 06:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM
Var resistor id
Its a Sylvania 400 oscilloscope. here is a clip of r-100. Would be nice to know the current required. Not listed in part...Martinj — 02:10 PM
The list of my radio & TV collection!
Thanks Richard. I hope you enjoy it. Here I have created an English section on the history of radio with videos in Engl...RadioSvit — 10:23 AM
The list of my radio & TV collection!
Hello RadioSvit, first all happy new year ! I will watch your new videos this week. Sincerely Richardradiorich — 09:19 AM

Who's Online

There are currently 8913 online users. [Complete List]
» 2 Member(s) | 8911 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me