1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Hello and a 37-675
gvel
Member
***
Posts: 78
Threads: 3
Joined: Mar 2011
City: Howell, MI
#19

07-24-2011, 12:30 PM
I'm back! Icon_wave

Well, I finally started, and the first task was the line filter bakelite block. This is the first block I've done. Yes - it was an adventure - but I accomplished this with out a heat gun. One must be careful with replacements. Redoing one of these would ruin the day! While it's out, I'll replace a couple of .005's next to it, since there's more room.

The single section filter caps will not get re-stuffed, but the 2 dual section filters probably will. There doesn't seem to be enough real-estate.

Once the filters are changed, I'll "fire" it up, and see where I'm at! If all goes well, the dreaded RF deck will be next!

Hope your summer is going well!

Time to mow!
-Greg
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Hello and a 37-675 - by gvel - 03-08-2011, 08:48 PM
RE: Hello and a 37-675 - by gvel - 04-18-2012, 06:03 PM
Re: Hello and a 37-675 - by TA Forbes - 03-08-2011, 10:35 PM
Re: Hello and a 37-675 - by TA Forbes - 03-08-2011, 10:37 PM
Re: Hello and a 37-675 - by 7estatdef - 03-08-2011, 11:10 PM
Re: Hello and a 37-675 - by TA Forbes - 03-09-2011, 08:58 AM
Re: Hello and a 37-675 - by Sean - 03-09-2011, 10:08 AM
Re: Hello and a 37-675 - by 7estatdef - 03-09-2011, 05:33 PM
Re: Hello and a 37-675 - by planigan - 03-09-2011, 11:53 PM
Re: Hello and a 37-675 - by Ron Ramirez - 03-10-2011, 09:55 AM
Re: Hello and a 37-675 - by planigan - 03-10-2011, 10:31 AM
Re: Hello and a 37-675 - by gvel - 03-10-2011, 08:18 PM
Re: Hello and a 37-675 - by planigan - 03-11-2011, 01:53 AM
Re: Hello and a 37-675 - by gvel - 03-11-2011, 07:53 AM
Re: Hello and a 37-675 - by gvel - 03-13-2011, 05:33 PM
Re: Hello and a 37-675 - by gvel - 03-27-2011, 12:56 PM
Re: Hello and a 37-675 - by planigan - 03-27-2011, 02:46 PM
Re: Hello and a 37-675 - by 7estatdef - 03-27-2011, 09:55 PM
Re: Hello and a 37-675 - by Jim Berg - 04-13-2011, 11:48 PM
Re: Hello and a 37-675 - by gvel - 07-24-2011, 12:30 PM
Re: Hello and a 37-675 - by gvel - 07-27-2011, 07:38 PM
Re: Hello and a 37-675 - by Ron Ramirez - 07-27-2011, 08:19 PM
Re: Hello and a 37-675 - by gvel - 07-27-2011, 09:34 PM
Re: Hello and a 37-675 - by gvel - 07-28-2011, 10:24 PM
Re: Hello and a 37-675 - by gvel - 08-07-2011, 09:20 PM
Re: Hello and a 37-675 - by codefox1 - 08-08-2011, 12:21 AM
Re: Hello and a 37-675 - by Ron Ramirez - 08-08-2011, 07:18 AM
Re: Hello and a 37-675 - by gvel - 08-09-2011, 07:32 PM
Re: Hello and a 37-675 - by codefox1 - 08-09-2011, 10:19 PM
Re: Hello and a 37-675 - by gvel - 08-10-2011, 09:43 AM
Re: Hello and a 37-675 - by gvel - 08-20-2011, 06:45 PM
Re: Hello and a 37-675 - by gvel - 08-21-2011, 07:15 PM
Re: Hello and a 37-675 - by gvel - 08-27-2011, 09:37 PM
Re: Hello and a 37-675 - by gvel - 08-28-2011, 04:21 PM
Re: Hello and a 37-675 - by Ron Ramirez - 08-28-2011, 05:18 PM
Re: Hello and a 37-675 - by gvel - 08-28-2011, 07:39 PM
Re: Hello and a 37-675 - by gvel - 09-07-2011, 10:47 AM
Re: Hello and a 37-675 - by gvel - 09-08-2011, 04:01 PM
Re: Hello and a 37-675 - by Ron Ramirez - 09-08-2011, 07:24 PM
Re: Hello and a 37-675 - by gvel - 09-09-2011, 11:12 AM
Re: Hello and a 37-675 - by gvel - 09-09-2011, 05:50 PM
Re: Hello and a 37-675 - by Ron Ramirez - 09-09-2011, 08:03 PM



Users browsing this thread: 12 Guest(s)
[-]
Recent Posts
Philco model 60
>>and found that the field coil is bad. Should be 1140 ohms, tests at 1.1k ohms. You have one stringent crit...morzh — 02:07 PM
Philco model 60
Yes I was there. I got some real bargains there. Plus a Zenith 7G605 clipper that I have been trying to find for a fair ...Radios1340 — 01:46 PM
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM

[-]
Who's Online
There are currently 7807 online users. [Complete List]
» 3 Member(s) | 7804 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration