Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 Getting Working or Complete Restoration??
#1

I just picked up a 38-116. It apears to be in pretty good condition aside from missing a few knobs and the back. Plugged it in and only got a humm and some crackling. On initial cleaning I noted a 6J5G tube and shield missing? Also, to clean the dust I removed the tubes one at a time cleaned and put back in position. The 5X4G tube had the center plastic with alignment snapped off at base and a red mark on base of tube (I assume for line up). Unfortunatly, I cannot find a mark where it plugs in.

Also, the unit seems to be floating and resting on the tuning control. If I lift up on the base or magnetic tuning shafts I can center it. Basically I hoped to get it working without complete restoration. Now I am leaning toward restoration as a winter project. Where do I start?

Where can I pick up a Icon_confused: manual and schematics for the radio? I have a little knowledge as I am a Ham Radio operator and built Heathkits in the old days.


Messages In This Thread
38-116 Getting Working or Complete Restoration?? - by Guest - 08-20-2006, 09:18 AM
[No subject] - by Terry Judkins - 08-20-2006, 11:20 PM
[No subject] - by Guest - 08-21-2006, 08:04 PM
5X4 position - by AI2V - 08-22-2006, 10:05 AM
[No subject] - by Guest - 08-22-2006, 07:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM

[-]
Who's Online
There are currently 7851 online users. [Complete List]
» 2 Member(s) | 7849 Guest(s)
AvatarAvatar

>