Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Capacitor Reliability Question
#1

First a Sea Story.

1983 I was on a USG trip to China, inter alia, to take a look at their manufactoring capabilities. In one particular factory, I was observing the capacitor production system. At the end of the process were some rather impressive looking capacitor testing machines. But they were testing the capacitors by hand. I watched one young lady testing about 60 units per minute but it seemed she would throw units in the "bad bucket" independent of what the meters on the testor said. When I asked why the reply was something to the effect "...we are very proud of our quality control, we test each unit individually. We are expected to find 10 percent that failed the test, no more no less." Thus the red light blinked bad unit, but it went in the "good bucket" and the green light blinked good and it went into the "bad" bucket. I exagerate somewhat, but in a nutshell that was what was going on.

My question is are there some bad apples as far as capacitors out there, exp electrolytics? Are the high voltage "mini electolytics" okay to use?

I pick on capacitors because I think they are the weak link in those old radios.


Messages In This Thread
Capacitor Reliability Question - by wakani - 10-12-2011, 10:33 PM
Re: Capacitor Reliability Question - by TA Forbes - 10-12-2011, 10:56 PM
Re: Capacitor Reliability Question - by Arran - 10-12-2011, 11:16 PM
Re: Capacitor Reliability Question - by Marsupial - 10-12-2011, 11:40 PM
Re: Capacitor Reliability Question - by Arran - 10-13-2011, 12:42 AM
Re: Capacitor Reliability Question - by TA Forbes - 10-18-2011, 12:10 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

[-]
Who's Online
There are currently no members online.

>