1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Alignment Question - 46-1213
wakani
Junior Member
**
Posts: 23
Threads: 12
Joined: Oct 2011
#4

12-30-2011, 01:57 PM
Now, all the votages look good, not too fond of the screen grid voltage on 1st and 2nd IF's but think OK. Found my VTVM was reading 1/2 DC voltage, so back to my Simpson VOM. All pin resistance checks are ok. Recallibrated my SigGen, lowered ouput level to bare minimum. Turned off my overhead flourescent light and now have some peaking in the IF transformers 1 but more on 2. Does not seem to have a "critical" peak that I remember from years ago ... but. Condenser trimmers super critical.

AM reception is very good (RF spewing lights turned off) with barely an aerial.

Thank you guys so much. Without your help I would not have the confidence to undertake this restoration. BZ to all.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Alignment Question - 46-1213 - by wakani - 12-29-2011, 11:28 PM
Re: Alignment Question - 46-1213 - by LASJayhawk - 12-30-2011, 12:44 AM
Re: Alignment Question - 46-1213 - by 7estatdef - 12-30-2011, 08:48 AM
Re: Alignment Question - 46-1213 - by wakani - 12-30-2011, 01:57 PM
Re: Alignment Question - 46-1213 - by 7estatdef - 12-30-2011, 09:48 PM
Re: Alignment Question - 46-1213 - by wakani - 12-30-2011, 11:01 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM

[-]
Who's Online
There are currently 5563 online users. [Complete List]
» 1 Member(s) | 5562 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration