1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Advice for a beginner
imacdaddy757
Junior Member
**
Posts: 32
Threads: 7
Joined: Jan 2012
#13

02-06-2012, 05:10 AM
WinkyDink, I've never immersed a set to clean it. I use brushes, compressed air and windex on a paper towel on Bakelite sets. Sometimes Q-tips to get into little grooves. But I'd not immerse a set that has an antenna or intact label inside. Far as labels, go ahead and cover any that remain with wide clear packing tape to preserve them - it's quite acceptable in restorations. If someone can't ID the set's model number in the future, it's really hard for them to get schematics or service it.
If it were my set, I would not take a glued-in antenna out. Just clean the area as I described above.

Regards,
Clarence
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Advice for a beginner - by winkydink - 01-23-2012, 09:51 AM
Re: Advice for a beginner - by imacdaddy757 - 01-25-2012, 07:42 PM
Re: Advice for a beginner - by dan mauro - 01-26-2012, 11:24 AM
Re: Advice for a beginner - by 37silverstreak - 01-27-2012, 01:21 PM
Re: Advice for a beginner - by imacdaddy757 - 01-28-2012, 06:33 AM
Re: Advice for a beginner - by dan mauro - 01-30-2012, 12:20 PM
Re: Advice for a beginner - by winkydink - 02-01-2012, 09:22 AM
Re: Advice for a beginner - by Dave - 02-01-2012, 07:53 PM
Re: Advice for a beginner - by winkydink - 02-02-2012, 03:15 PM
Re: Advice for a beginner - by imacdaddy757 - 02-02-2012, 07:49 PM
Re: Advice for a beginner - by winkydink - 02-02-2012, 09:17 PM
Re: Advice for a beginner - by winkydink - 02-03-2012, 10:50 AM
Re: Advice for a beginner - by imacdaddy757 - 02-06-2012, 05:10 AM
Re: Advice for a beginner - by Bob Andersen - 02-06-2012, 05:25 PM
Re: Advice for a beginner - by codefox1 - 02-06-2012, 05:37 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM
Philco model 60
Plus I forgot that I have a spare complete Philco FC speaker, that would work perfectly, now that I don’t need it. Got i...Radios1340 — 05:36 PM

[-]
Who's Online
There are currently 5157 online users. [Complete List]
» 1 Member(s) | 5156 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration