1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-610 IF Can covers
RichardG
Unregistered
 
#5

02-07-2012, 08:08 PM
Thanks, Ron.

I agree that is what should happen, but with nut removed, clips off the side, the can will not slide off.

So I am going to desolder it tonight and see what gives. I am presuming due to the nature of the problem I have a broken/loose wire somewhere in the can, and I should put on some new wiring in any case. After all, this has got to be simpler than that RF section (?).

Just obtained a 40-150 as the next project, but have to get this one buttoned up first. I presume this new acquisition will have a lot of rubber wiring, and having redone a few Crosleys of that era, I know what to expect.

BTW, love the site. This is a great service to all us rookie Philco Phanatics.

Richard
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
37-610 IF Can covers - by RGallahue - 02-05-2012, 01:55 PM
Re: 37-610 IF Can covers - by codefox1 - 02-05-2012, 03:17 PM
Re: 37-610 IF Can covers - by RGallahue - 02-05-2012, 03:55 PM
Re: 37-610 IF Can covers - by Ron Ramirez - 02-05-2012, 06:12 PM
Re: 37-610 IF Can covers - by RichardG - 02-07-2012, 08:08 PM
Re: 37-610 IF Can covers - by codefox1 - 02-08-2012, 11:45 AM
Re: 37-610 IF Can covers - by RGallahue - 02-08-2012, 09:11 PM
Re: 37-610 IF Can covers - by codefox1 - 02-08-2012, 11:25 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration