Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Majestic 181
#2

Warping pot metal in the tuning capacitors seems to have been a problem with many American Grigsby Grunow Majestics from that era, I haven't run into that problem in any Canadian Rogers made Majestics from those years though, even though the chassis and circuits are very similar. There are ways of repairing the problem apparently, although as with anything like that it isn't a job for those who are not mechanically inclined or have experience with such things.
Regards
Arran


Messages In This Thread
Majestic 181 - by Jayce - 03-23-2012, 11:42 PM
RE: Majestic 181 - by Arran - 03-24-2012, 02:34 AM
RE: Majestic 181 - by Jayce - 03-24-2012, 01:03 PM
RE: Majestic 181 - by Arran - 03-24-2012, 09:26 PM
RE: Majestic 181 - by Ron Ramirez - 03-24-2012, 09:44 PM
RE: Majestic 181 - by Jayce - 03-24-2012, 10:43 PM
RE: Majestic 181 - by Jayce - 03-24-2012, 10:40 PM
RE: Majestic 181 - by Doug Houston - 03-25-2012, 12:56 AM
RE: Majestic 181 - by TA Forbes - 03-25-2012, 12:57 AM
RE: Majestic 181 - by Jayce - 03-25-2012, 01:18 AM
RE: Majestic 181 - by Doug Houston - 03-25-2012, 09:33 PM
RE: Majestic 181 - by Jayce - 03-25-2012, 10:51 PM
RE: Majestic 181 - by Arran - 03-26-2012, 12:05 AM
RE: Majestic 181 - by Doug Houston - 03-26-2012, 11:14 PM
RE: Majestic 181 - by TA Forbes - 03-27-2012, 01:54 PM
RE: Majestic 181 - by codefox1 - 03-27-2012, 09:03 PM
RE: Majestic 181 - by Doug Houston - 04-05-2012, 11:19 PM
RE: Majestic 181 - by Arran - 03-27-2012, 07:43 PM
RE: Majestic 181 - by Jayce - 03-29-2012, 07:56 PM
RE: Majestic 181 - by Arran - 04-03-2012, 11:30 PM
RE: Majestic 181 - by Doug Houston - 03-29-2012, 11:53 PM
RE: Majestic 181 - by Jayce - 04-04-2012, 12:39 AM
RE: Majestic 181 - by codefox1 - 04-04-2012, 02:57 AM
RE: Majestic 181 - by Arran - 04-05-2012, 01:26 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM

[-]
Who's Online
There are currently 9218 online users. [Complete List]
» 5 Member(s) | 9213 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>