philco 48-214 code 125 Cap ?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

philco 48-214 code 125 Cap ?

Arran
Phorum Expert

Posts: 4,821
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA

#9

05-23-2012, 11:25 PM

If the set uses a 35Y4, a 35Z5, or a 35W4 tube then it likely has one of two things wrong:
(1) The rectifier tube heater is open between the pilot light tap and one end of the tube heater.
(2 The resistor paralleled with the pilot light is open circuit or blown. With some tubes like the 35Y4 it may or may not have a resistor paralleled with the pilot light depending on the amperage of the pilot light bulb used.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 01:18 PM

RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-20-2012, 02:17 PM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-20-2012, 03:10 PM

RE: philco 48-214 code 125 Cap ? - by Arran - 05-20-2012, 09:18 PM

RE: philco 48-214 code 125 Cap ? New problem - by Eric - 05-23-2012, 05:24 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 08:37 PM

RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-23-2012, 09:07 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-23-2012, 09:10 PM

RE: philco 48-214 code 125 Cap ? - by Arran - 05-23-2012, 11:25 PM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-24-2012, 09:28 AM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-24-2012, 03:14 PM

RE: philco 48-214 code 125 Cap ? - by codefox1 - 05-24-2012, 10:13 PM

RE: philco 48-214 code 125 Cap ? - by Eric - 05-29-2012, 03:08 PM

RE: philco 48-214 code 125 Cap ? - by 7estatdef - 05-30-2012, 07:15 AM

RE: philco 48-214 code 125 Cap ? - by morzh - 05-30-2012, 08:25 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
The speaker table error?
G 10-1/2" 65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H 10-1/2" 77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth! I hope the final result is as much a quality sounding example! Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

Who's Online
There are currently no members online.