Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tube Testing - 46-200
#4

Schematic here:

http://www.nostalgiaair.org/PagesByModel...013591.pdf

Sounds like this one was hacked. No telling what else may be wrong, but if you can't get your money back :

The 7C6 is completely wrong for this set and will not perform well if at all. Completely different heater voltage and current. Get the correct tube. Don't have an extra 14B6. but would give it to you if I did.

Chuck is right. Check antenna loop, should be 3.2 ohms per schematic, and external antenna lug should be grounded to chassis. It will hum terribly if there is no loop antenna.

If the pilot light works and there is adequate B+ I'd leave the rectifier alone.

Also look for evidence (or lack thereof) of filter and paper capacitors having been changed.

Let us know.


Messages In This Thread
Tube Testing - 46-200 - by winkydink - 08-19-2012, 09:45 AM
RE: Tube Testing - 46-200 - by Ron Ramirez - 08-19-2012, 10:27 AM
RE: Tube Testing - 46-200 - by winkydink - 08-19-2012, 11:29 AM
RE: Tube Testing - 46-200 - by codefox1 - 08-19-2012, 01:01 PM
RE: Tube Testing - 46-200 - by Paul Philco322 - 08-19-2012, 08:17 PM
RE: Tube Testing - 46-200 - by winkydink - 08-20-2012, 08:37 AM
RE: Tube Testing - 46-200 - by Ron Ramirez - 08-20-2012, 08:45 AM
RE: Tube Testing - 46-200 - by codefox1 - 08-20-2012, 01:17 PM
RE: Tube Testing - 46-200 - by winkydink - 08-20-2012, 01:26 PM
RE: Tube Testing - 46-200 - by codefox1 - 08-20-2012, 01:53 PM
RE: Tube Testing - 46-200 - by Ron Ramirez - 08-20-2012, 04:29 PM
RE: Tube Testing - 46-200 - by winkydink - 08-20-2012, 09:47 PM
RE: Tube Testing - 46-200 - by winkydink - 09-04-2012, 08:29 AM
RE: Tube Testing - 46-200 - by Ron Ramirez - 09-04-2012, 08:44 AM
RE: Tube Testing - 46-200 - by winkydink - 09-04-2012, 08:58 AM
RE: Tube Testing - 46-200 - by Ron Ramirez - 09-04-2012, 09:22 AM
RE: Tube Testing - 46-200 - by TimC - 09-07-2012, 10:26 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM
A Marconi model 86
Dan Double conversion is using two IF converters instead of one. This improves the image response. morzh — 07:15 PM

[-]
Who's Online
There are currently no members online.

>