Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tube question
#10

Eric, here is quick and dirty troubleshooting procedure. First, holding a capacitor (value not critical .01 or so would be good) in your fingers by one lead, touch the other lead to the center terminal (the wiper) of the volume control. You should hear a hum in the speaker. If so, the audio section is working, at least in some fashion. Next, tune the radio to mid band, say 800kc. Now take a portable radio tuned to 1255 (800 + 455) and place it near your Emerson. Now rock the tuning slightly on either one of the radios. The portable should pick up the local oscillator of the radio under test. By doing these two test, you will prove (or disprove) about 2/3 of the radio circuit.

Steve

M R Radios   C M Tubes


Messages In This Thread
Tube question - by Eric - 08-27-2012, 05:26 PM
RE: Tube question - by rghines1 - 08-27-2012, 07:37 PM
RE: Tube question - by Eric - 08-27-2012, 08:21 PM
RE: Tube question - by Arran - 08-28-2012, 01:02 AM
RE: Tube question - by Eric - 08-28-2012, 12:15 PM
RE: Tube question - by codefox1 - 08-28-2012, 02:12 PM
RE: Tube question - by Eric - 08-28-2012, 04:05 PM
RE: Tube question - by Arran - 08-29-2012, 07:46 PM
RE: Tube question - by Eric - 09-01-2012, 10:47 PM
RE: Tube question - by Steve Davis - 09-02-2012, 02:31 PM
RE: Tube question - by Eric - 09-03-2012, 10:00 AM
RE: Tube question - by 7estatdef - 09-03-2012, 04:47 PM
RE: Tube question - by Eric - 09-04-2012, 03:44 PM
RE: Tube question - by 7estatdef - 09-04-2012, 05:26 PM
RE: Tube question - by Eric - 09-06-2012, 01:20 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 91 Tuning Condenser
Hello, Does anyone know how the dial plate comes off the tuning condenser shaft? The dial itself id so warped I can't...dconant — 06:01 PM
Eico 368 TV/FM Sweep Generator
Ron, for the future: In order to change the name of teh topic, 1. Go to the very first post. 2. Hit "Edit...morzh — 04:29 PM
6TPZ and 5TPO Radio Help
Transistors are easy. No converters. If you have input voltage, then just put some signal through. Or touch your fin...morzh — 04:25 PM
462ron
Hi Mike, I believe I tried different ways to change the header for my post but no luck. Anyway thanks for changing it fo...462ron — 04:02 PM
6TPZ and 5TPO Radio Help
Since these radios operated in harsh environments (temp changes and vibration) you could touch a soldering iron to all t...GarySP — 03:18 PM
6TPZ and 5TPO Radio Help
Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM

[-]
Who's Online
There are currently 9343 online users. [Complete List]
» 2 Member(s) | 9341 Guest(s)
AvatarAvatar

>