Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Crosley 515 trouble shooting
#6

Eric, yes this is what I said before - they are tied together. Obviously the voltahe then will be the same.
I do not know whether there is a rule of setting the radio controls when measuring voltages and if that involves setting the volume control to max.

If this is the case then yes, the voltage at the Cathode and Suppressor will be at the minimum, as the Chassis through the wiper connects practically directly to that point. Usually the potentiometer will have some residual resistance there, not exactly zero, so this probably will cause the voltage to be a bit different from zero.
At the minimum volume the voltage may be high but again, without knowing the values (this document lists only part numbers) I cannot tell you what it will be.

if you know the B+ voltage and all the resistors' values, plus the full scale value of the volume pot, then you can easily calculate it as V=(B+ * Vol_pot)/(21Z+21Y+Vol_pot).


Messages In This Thread
Crosley 515 trouble shooting - by Eric - 02-17-2013, 05:31 PM
RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 07:35 PM
RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 08:57 PM
RE: Crosley 515 trouble shooting - by morzh - 02-17-2013, 10:27 PM
RE: Crosley 515 trouble shooting - by Eric - 02-17-2013, 11:36 PM
RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 10:55 AM
RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 01:01 PM
RE: Crosley 515 trouble shooting - by morzh - 02-18-2013, 09:06 PM
RE: Crosley 515 trouble shooting - by Eric - 02-18-2013, 09:43 PM
RE: Crosley 515 trouble shooting - by morzh - 02-19-2013, 05:30 PM
RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 06:21 PM
RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 07:12 PM
RE: Crosley 515 trouble shooting - by Eric - 02-20-2013, 09:14 PM
RE: Crosley 515 trouble shooting - by morzh - 02-20-2013, 09:41 PM
RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 09:00 AM
RE: Crosley 515 trouble shooting - by Eric - 02-21-2013, 10:33 AM
RE: Crosley 515 trouble shooting - by morzh - 02-21-2013, 05:28 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 10:25 AM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 11:03 AM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 05:03 PM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 05:40 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 07:36 PM
RE: Crosley 515 trouble shooting - by Eric - 02-22-2013, 09:17 PM
RE: Crosley 515 trouble shooting - by morzh - 02-22-2013, 09:41 PM
RE: Crosley 515 trouble shooting - by 7estatdef - 02-23-2013, 06:48 PM
RE: Crosley 515 trouble shooting - by morzh - 02-23-2013, 07:30 PM
RE: Crosley 515 trouble shooting - by lumberman22 - 03-30-2014, 01:38 PM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM

[-]
Who's Online
There are currently no members online.

>