Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My first set: Philco 40-180
#14

Thank you for all of the opinions! I REALLY appreciate all of you thoughtful wisdom and advice! I had some goop in the house, so I gathered a few old rags and went to work.

One hour later and W*O*W !!!!! I found about 99% of the original finish hiding under a ton of grime! Many of the lighter spots have been removed or filled in with the dirt that the goop loosened. There are a few places where it looks like whatever liquid was spilled on the cabinet has eaten into the lacquer finish, but you can really only see it if the light reflects in just the right way.

The surface shows lots of little cracks and a fair amount of roughness, perhaps I'll explore adding a top coat, but for now, I'm EXTREMELY pleased! I will post a few pictures tomorrow.
What a beauty! I would have happily paid much more had I known what was hiding under 73 years of grime!


Messages In This Thread
My first set: Philco 40-180 - by EricS - 08-22-2013, 04:03 PM
RE: My first set: Philco 40-180 - by codefox1 - 08-22-2013, 06:19 PM
RE: My first set: Philco 40-180 - by Jamie - 08-22-2013, 07:25 PM
RE: My first set: Philco 40-180 - by EricS - 08-22-2013, 09:13 PM
RE: My first set: Philco 40-180 - by EricS - 08-22-2013, 09:36 PM
RE: My first set: Philco 40-180 - by Arran - 08-23-2013, 12:22 AM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 10:10 AM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 05:26 PM
RE: My first set: Philco 40-180 - by Jamie - 08-23-2013, 07:18 PM
RE: My first set: Philco 40-180 - by EricS - 08-23-2013, 09:49 PM
RE: My first set: Philco 40-180 - by EricS - 08-24-2013, 05:55 PM
RE: My first set: Philco 40-180 - by EricS - 08-24-2013, 07:56 PM
RE: My first set: Philco 40-180 - by codefox1 - 08-25-2013, 04:03 PM
RE: My first set: Philco 40-180 - by EricS - 08-25-2013, 08:59 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 01:56 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 07:09 PM
RE: My first set: Philco 40-180 - by EricS - 08-26-2013, 07:34 PM
RE: My first set: Philco 40-180 - by Jamie - 08-26-2013, 08:12 PM
RE: My first set: Philco 40-180 - by EricS - 08-27-2013, 09:58 AM
RE: My first set: Philco 40-180 - by EricS - 08-29-2013, 11:24 AM
RE: My first set: Philco 40-180 - by EricS - 09-03-2013, 04:41 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM
6TPZ and 5TPO Radio Help
I suspect it's been repaired before. And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM

[-]
Who's Online
There are currently 10598 online users. [Complete List]
» 3 Member(s) | 10595 Guest(s)
AvatarAvatarAvatar

>