Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#17

Thanks, I'll see if my local electronics shop has any...

Edit:

No luck. I have to go to the Internet. Any decent sources for these? I cannot locate any 6000pF caps, only 4700pF.

So what can I do? 4700 is enough, 10000 too much, or should I wire 3 2200's in parallel (I'd rather not tempt the fates of MTBF this way)?

Also there is one other silver mica capacitor in there - it's part 6A on the schematic. The problem is it's listed as a 20mfd device and there's no way this is 20mfd, it's just way too small. Elsewhere on the schematic it's listed as 20mmfd, which makes a lot more sense for this type of capacitor.


Messages In This Thread
Restoring a 39-7 - by rworne - 08-15-2013, 10:34 AM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 03:18 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 03:27 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 03:34 PM
RE: Restoring a 39-7 - by BrendaAnnD - 08-30-2013, 05:13 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 05:22 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 06:05 PM
RE: Restoring a 39-7 - by morzh - 08-30-2013, 06:17 PM
RE: Restoring a 39-7 - by jerryhawthorne - 08-30-2013, 06:29 PM
RE: Restoring a 39-7 - by rworne - 08-30-2013, 06:52 PM
RE: Restoring a 39-7 - by Arran - 08-30-2013, 10:42 PM
RE: Restoring a 39-7 - by rworne - 08-31-2013, 12:32 AM
RE: Restoring a 39-7 - by Jamie - 08-31-2013, 02:36 PM
RE: Restoring a 39-7 - by rworne - 08-31-2013, 03:25 PM
RE: Restoring a 39-7 - by hunter2115 - 09-05-2013, 09:31 PM
RE: Restoring a 39-7 - by morzh - 09-05-2013, 09:38 PM
RE: Restoring a 39-7 - by rworne - 09-05-2013, 11:12 PM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 09:49 AM
RE: Restoring a 39-7 - by Mondial - 10-22-2013, 09:54 AM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 10:14 AM
RE: Restoring a 39-7 - by Radioroslyn - 10-22-2013, 05:53 PM
RE: Restoring a 39-7 - by rworne - 10-22-2013, 08:28 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM

[-]
Who's Online
There are currently 9952 online users. [Complete List]
» 3 Member(s) | 9949 Guest(s)
AvatarAvatarAvatar

>