1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Knob glued to shaft
klondike98
Phorum Moderator
******
Posts: 5,124
Threads: 271
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#1

09-12-2013, 07:05 PM
Icon_sad has anyone faced a knob that has been glued to the shaft of a switch??
Any ideas on getting it off? I'm almost at the point of trying to cut the shaft and then try to find a new switch an knob. With the chassis loose I can get a small space between the knob and the cabinet but that's my last resort.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Knob glued to shaft - by klondike98 - 09-12-2013, 07:05 PM
RE: Knob glued to shaft - by murf - 09-12-2013, 07:14 PM
RE: Knob glued to shaft - by Jamie - 09-12-2013, 07:18 PM
RE: Knob glued to shaft - by klondike98 - 09-12-2013, 07:41 PM
RE: Knob glued to shaft - by Jamie - 09-12-2013, 07:46 PM
RE: Knob glued to shaft - by Arran - 09-12-2013, 07:48 PM
RE: Knob glued to shaft - by klondike98 - 09-12-2013, 07:52 PM
RE: Knob glued to shaft - by Jamie - 09-12-2013, 08:28 PM
RE: Knob glued to shaft - by klondike98 - 09-12-2013, 08:44 PM
RE: Knob glued to shaft - by klondike98 - 09-13-2013, 02:15 PM
RE: Knob glued to shaft - by klondike98 - 09-13-2013, 07:57 PM
RE: Knob glued to shaft - by murf - 09-13-2013, 08:34 PM
RE: Knob glued to shaft - by EricS - 09-17-2013, 07:58 PM
RE: Knob glued to shaft - by klondike98 - 09-17-2013, 09:18 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM

[-]
Who's Online
There are currently 11359 online users. [Complete List]
» 2 Member(s) | 11357 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration