1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 024 Signal Generator
marty
Member
***
Posts: 240
Threads: 27
Joined: Jun 2013
City: Boulder, Colorado
#1

09-28-2013, 06:51 PM
Hi All;
I have the Philco 024 Signal Generator, and I have ordered the Papers (Documents) from Chuck for it and they are a week or more away..
But, in the mean time can anyone tell me if there are three power wires or four power wires ?? As near as I can tell I have three wires that I assume are for power, but it could be missing a wire.. Two (I think) of what I have are for the filament one going thru the switch which is missing and I have put in.. The other one of the three is for the +90 Volts, its -side of the 90 volts that I am not sure of.. Does it go to one of the filament wires which would make it a three wire setup, Or does it go to Ground which I would then have a four wire setup and I am missing that wire..
THANK YOU Marty
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 024 Signal Generator - by marty - 09-28-2013, 06:51 PM
RE: Philco 024 Signal Generator - by Radioroslyn - 09-28-2013, 08:02 PM
RE: Philco 024 Signal Generator - by marty - 09-28-2013, 09:06 PM
RE: Philco 024 Signal Generator - by Radioroslyn - 09-28-2013, 09:17 PM
RE: Philco 024 Signal Generator - by marty - 09-28-2013, 09:32 PM
RE: Philco 024 Signal Generator - by Jamie - 09-28-2013, 09:55 PM
RE: Philco 024 Signal Generator - by Warren - 09-28-2013, 11:38 PM
RE: Philco 024 Signal Generator - by marty - 09-29-2013, 09:21 AM
RE: Philco 024 Signal Generator - by marty - 10-07-2013, 08:13 PM
RE: Philco 024 Signal Generator - by Tonytiger75 - 05-13-2019, 02:18 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Atwater-Kent 84, restoration.
Hello Mike, Wow ! far as my AK it does work and the cabinet is in nice shape so is my chassis anyway here is a photo of...radiorich — 02:59 AM
Atwater-Kent 84, restoration.
Nice radio, Mike! Here's hoping it was well rebuilt. Take care and BE HEALTHY! GaryGarySP — 12:12 AM
Atwater-Kent 84, restoration.
Rich yes, this is the way I got it. I have just put it on the table and took it apart. I suspect it even might work,...morzh — 11:31 PM
Atwater-Kent 84, restoration.
Hello mike, What nice looking radio I have one AK in my collection it's a console I have not started restoring it yet ....radiorich — 11:21 PM
91H Code 126 Restore
Just to make it more confusing here is another model 91 schematic that doesn't show parts with dotted lines in that spot...Arran — 10:37 PM
Atwater-Kent 84, restoration.
The wires were desoldered from the can, and the capacitors checked. All checked at 0.102 uF, which is correct. So the c...morzh — 09:41 PM
An attempt to remove the Field Coil from a G speaker
Arran Yours probably then the H speaker, same as mine.morzh — 08:39 PM
An attempt to remove the Field Coil from a G speaker
Mike; I would like to have a look at the speaker in my model 96, but the set is packed into a corner in the basement. ...Arran — 08:04 PM
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM

[-]
Who's Online
There are currently 4609 online users. [Complete List]
» 3 Member(s) | 4606 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration