Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Station setter info
#6

Chuck Schwark Wrote:The Dealer/Service would setup the Station Setter for the local stations and some of the receivable "biggies" and beat the Setter's preset freqs against the tuned-in stations for setting the radio's pushbuttons dead on freq.

Actually its biggest usefulness was setting the pushbuttons when stations were NOT on the air. In those days the smaller stations weren't necessarily on the air all day. This was the case in my hometown when they went off from about 2-4 PM well into the 60s (when a second station finally came to town) Icon_wink

It also enabled the serviceman to set the buttons for some nighttime stations that could not be heard during the day.

I had an RCA version. It was ac or battery operated and used a 6H6 as a rectifier. I forget was the 'business' tube was.

-Bill


Messages In This Thread
Philco Station setter info - by gary rabbitt - 05-18-2008, 02:27 AM
[No subject] - by Ron Ramirez - 05-19-2008, 11:25 PM
[No subject] - by Chuck Schwark - 05-20-2008, 09:17 AM
[No subject] - by Ron Ramirez - 05-20-2008, 06:26 PM
[No subject] - by Chuck Schwark - 05-20-2008, 07:33 PM
[No subject] - by exray - 05-20-2008, 09:09 PM
[No subject] - by gary rabbitt - 05-20-2008, 11:35 PM
[No subject] - by Ron Ramirez - 05-21-2008, 06:46 AM
[No subject] - by Chuck Schwark - 05-21-2008, 12:57 PM
[No subject] - by Chuck Schwark - 05-22-2008, 04:15 PM
[No subject] - by gary rabbitt - 05-27-2008, 12:33 AM
[No subject] - by Chuck Schwark - 05-27-2008, 10:48 AM
[No subject] - by gary rabbitt - 06-03-2008, 06:13 PM
[No subject] - by Chuck Schwark - 06-03-2008, 10:59 PM
[No subject] - by gary rabbitt - 06-04-2008, 02:37 AM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM

[-]
Who's Online
There are currently 9903 online users. [Complete List]
» 2 Member(s) | 9901 Guest(s)
AvatarAvatar

>