emerson 557 ?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

emerson 557 ?

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#13

01-08-2014, 07:59 PM

I used detox to clean the switch I might be able to use an emery board or a small piece of scotch brite if I can get it in there. I have removed one of the IF's T6 I think (my print is bad) it is connected to the 19T8 as it is listed as the am detector, The coils were good. should I look at the 12BA7 circuit? I don't want to open any coils I don't have to as I'm afraid of damaging one where there was nothing wrong.

Find

« Next Oldest | Next Newest »

Messages In This Thread

emerson 557 ? - by Eric - 12-10-2013, 01:06 PM

RE: emerson 557 ? - by BrendaAnnD - 12-10-2013, 05:08 PM

RE: emerson 557 ? - by Eric - 12-10-2013, 06:58 PM

RE: emerson 557 ? - by BrendaAnnD - 12-10-2013, 08:46 PM

RE: emerson 557 ? - by morzh - 12-10-2013, 10:12 PM

RE: emerson 557 ? - by Eric - 12-11-2013, 10:28 AM

RE: emerson 557 ? - by morzh - 12-11-2013, 12:36 PM

RE: emerson 557 ? - by Eric - 12-11-2013, 05:04 PM

RE: emerson 557 ? - by jerryhawthorne - 12-11-2013, 05:52 PM

RE: emerson 557 ? - by Eric - 01-08-2014, 03:52 PM

RE: emerson 557 ? - by morzh - 01-08-2014, 04:30 PM

RE: emerson 557 ? - by BrendaAnnD - 01-08-2014, 07:41 PM

RE: emerson 557 ? - by Eric - 01-08-2014, 07:59 PM

RE: emerson 557 ? - by morzh - 01-08-2014, 08:17 PM

RE: emerson 557 ? - by Eric - 01-08-2014, 08:44 PM

RE: emerson 557 ? - by BrendaAnnD - 01-08-2014, 09:29 PM

RE: emerson 557 ? - by Eric - 01-09-2014, 06:31 PM

RE: emerson 557 ? - by hsusmann - 01-09-2014, 07:00 PM

RE: emerson 557 ? - by morzh - 01-09-2014, 07:30 PM

RE: emerson 557 ? - by Eric - 01-09-2014, 08:25 PM

RE: emerson 557 ? - by morzh - 01-09-2014, 09:30 PM

RE: emerson 557 ? - by Eric - 01-10-2014, 03:55 PM

RE: emerson 557 ? - by jerryhawthorne - 01-10-2014, 05:40 PM

RE: emerson 557 ? - by Eric - 01-10-2014, 07:54 PM

RE: emerson 557 ? - by jerryhawthorne - 01-10-2014, 09:55 PM

RE: emerson 557 ? - by Eric - 01-11-2014, 10:21 AM

RE: emerson 557 ? - by jerryhawthorne - 01-11-2014, 02:38 PM

RE: emerson 557 ? - by Eric - 01-11-2014, 07:23 PM

RE: emerson 557 ? - by jerryhawthorne - 01-11-2014, 07:56 PM

RE: emerson 557 ? - by Eric - 01-12-2014, 11:03 AM

RE: emerson 557 ? - by Eric - 02-11-2014, 05:54 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

Who's Online
There are currently no members online.