Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grunow Teledial
#20

I wonder if all versions of these had the same lousy band spread on short wave? Note how it goes from 5.5 to 18 mc on a single band, pretty much like the non Teledial Grunow that Bob Andersen has. In spite of this they used a sweep hand for logging, which seems almost like a waste of time. On my G.E M-83 they used five bands, longwave, broadcast, and three shortwave bands.
With regard to using 6F6s or 6L6 tubes as final outputs, that could be because of marketing, or simply because G.H.U managed to get a deal on 6L6 tubes in bulk. Apparently this was done with one of the brand Z models, they fitted the set with 6L6 outputs for marketing purposes, just to make it look like an audio "Hot Rod", but the 6L6s didn't do very much since the power supply didn't give them the extra B+ voltage they needed, just the usual 225-250 volts.
Regards
Arran


Messages In This Thread
Grunow Teledial - by Jayce - 02-28-2014, 11:23 PM
RE: Grunow Teledial - by murf - 02-28-2014, 11:55 PM
RE: Grunow Teledial - by Jayce - 03-01-2014, 01:01 AM
RE: Grunow Teledial - by morzh - 03-01-2014, 01:05 AM
RE: Grunow Teledial - by TA Forbes - 03-01-2014, 09:33 AM
RE: Grunow Teledial - by TA Forbes - 03-01-2014, 09:35 AM
RE: Grunow Teledial - by Jayce - 03-01-2014, 11:30 AM
RE: Grunow Teledial - by Gene Pederson - 03-01-2014, 03:21 PM
RE: Grunow Teledial - by Arran - 03-02-2014, 12:32 AM
RE: Grunow Teledial - by PhilcoJohn - 03-02-2014, 09:43 AM
RE: Grunow Teledial - by morzh - 03-02-2014, 01:46 PM
RE: Grunow Teledial - by Gene Pederson - 03-02-2014, 02:32 PM
RE: Grunow Teledial - by Ronin61 - 03-02-2014, 04:23 PM
RE: Grunow Teledial - by Ronin61 - 03-02-2014, 04:27 PM
RE: Grunow Teledial - by Ronin61 - 03-02-2014, 04:32 PM
RE: Grunow Teledial - by Jayce - 03-02-2014, 07:58 PM
RE: Grunow Teledial - by TA Forbes - 03-02-2014, 08:26 PM
RE: Grunow Teledial - by Ronin61 - 03-02-2014, 08:57 PM
RE: Grunow Teledial - by Jayce - 03-02-2014, 09:16 PM
RE: Grunow Teledial - by Arran - 03-03-2014, 02:14 AM
RE: Grunow Teledial - by Gene Pederson - 03-03-2014, 04:01 PM
RE: Grunow Teledial - by Jayce - 03-03-2014, 05:55 PM
RE: Grunow Teledial - by Jayce - 03-04-2014, 10:01 PM
RE: Grunow Teledial - by jamr005 - 09-25-2019, 04:38 PM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
42-345 Resistors
Pholks: What are these little cylindrical objects inside Little Phil? They seem hollow. I don't think they are capacito...proftrussell — 12:39 AM
[split] New member...
Well, the paint thinner didn't get the job done but some heat did.  I got it apart, got everything cleaned up, re-lubed,...HowardWoodard — 12:24 AM
[split] New member...
The gear on the 37-604 is exact same, but there was no pin. The pin exists on the gear of 37-116 or those ones with rob...morzh — 04:31 PM
Philco 46-480 Electronic Restoration
I agree, the two should not be connected. Due to poor image quality of the original Philco schematic, it was unclear if ...jrblasde — 02:25 PM
New 37-116 Parts
Dan, I'm curious, I saw the 38-2 dial you got from them. Are you getting a new, improved one from them without the wh...Greg — 01:59 PM
New 37-116 Parts
They are not closed. I sent an email to them 3/8/2025 and got a reply back 3/10/2025. Since 3/8/2025 was a Saturday I di...dconant — 01:22 PM
Gloritone 27 Radio
Hello, The radio is playing now using the repaired antenna coil. MrFixr55 you stated a while back I might need to add...dconant — 01:10 PM
New 37-116 Parts
Well, their answering machine says they check their messages every day at noon and respond by 3p the next day - I can sa...Doppleganger — 01:09 PM
[split] New member...
Thanks 462ron. I have it soaking right now but will test the power of my shop light magnet on the pin when it comes out.HowardWoodard — 11:39 AM
Philco 46-480 Electronic Restoration
Wasn't that the Suppressor grid that we were talking about, that got connected with the AVC? Anywho, the initial questi...morzh — 10:53 AM

[-]
Who's Online
There are currently no members online.

>