Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco D-10 needle source
#7

You guys must be referring to that "Dynamic" cartridge Philco came out with right after WWII. Yes, the styli for those are basically unobtainium. To make matters worse, Philco designed the cartridge to only accept Philco's own proprietary stylus; use of a steel needle or the generic sapphire needle will destroy the cone of the cartridge which the stylus slips into.

A newer magnetic cartridge would seem to be an answer to the problem, until you consider that Philco set the mounting holes too far back for a modern cartridge.

Sometimes companies did some really dumb things in order to be different from their competitors...but then again, Philco didn't expect anyone to still be using 46-1209 sets 68 years later.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco D-10 needle source - by brownie45 - 05-28-2014, 08:37 AM
RE: Philco D-10 needle source - by TA Forbes - 05-28-2014, 10:50 AM
RE: Philco D-10 needle source - by brownie45 - 05-28-2014, 12:48 PM
RE: Philco D-10 needle source - by sam - 05-28-2014, 01:18 PM
RE: Philco D-10 needle source - by Warren - 05-28-2014, 01:56 PM
RE: Philco D-10 needle source - by TA Forbes - 05-28-2014, 11:17 PM
RE: Philco D-10 needle source - by Ron Ramirez - 05-29-2014, 05:42 AM
RE: Philco D-10 needle source - by brownie45 - 05-29-2014, 06:58 AM
RE: Philco D-10 needle source - by Randy H. - 06-09-2014, 07:11 PM
RE: Philco D-10 needle source - by Ron Ramirez - 06-09-2014, 08:18 PM
RE: Philco D-10 needle source - by brownie45 - 06-09-2014, 09:39 PM
RE: Philco D-10 needle source - by Randy H. - 06-13-2014, 05:46 PM
RE: Philco D-10 needle source - by Ron Ramirez - 06-13-2014, 06:00 PM
RE: Philco D-10 needle source - by Skip - 06-13-2014, 06:11 PM
RE: Philco D-10 needle source - by Warren - 06-13-2014, 10:22 PM
RE: Philco D-10 needle source - by w4rtc - 06-14-2014, 07:53 AM
RE: Philco D-10 needle source - by brownie45 - 06-15-2014, 12:24 PM
RE: Philco D-10 needle source - by w4rtc - 06-15-2014, 05:01 PM
RE: Philco D-10 needle source - by brownie45 - 06-15-2014, 07:02 PM
RE: Philco D-10 needle source - by Warren - 06-15-2014, 08:29 PM
RE: Philco D-10 needle source - by w4rtc - 06-15-2014, 11:22 PM
RE: Philco D-10 needle source - by Warren - 06-16-2014, 01:53 AM
RE: Philco D-10 needle source - by w4rtc - 06-16-2014, 10:35 AM



Users browsing this thread: 10 Guest(s)
[-]
Recent Posts
Philco model 60
Yes I was there. I got some real bargains there. Plus a Zenith 7G605 clipper that I have been trying to find for a fair ...Radios1340 — 01:46 PM
The speaker table error?
G  10-1/2"       65, 76, 87, 95 Push-Pull 45's 2766 0.7 550 3200 H   10-1/2"    77, 96 Push-Pull...morzh — 09:26 PM
A Marconi model 86
I have a Stromberg, one of the early ones, seems early 30s. This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM
A Marconi model 86
A backbreaker.....PaulPaul Philco322 — 08:12 PM
A Marconi model 86
>>What a behemoth! A Juggernaut.morzh — 07:47 PM
Philco 70 antenna lead
I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM
A Marconi model 86
:e_biggrin: What a behemoth!  I hope the final result is as much a quality sounding example!  Keep us posted on your pro...GarySP — 07:32 PM
A Marconi model 86
I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM
Philco 70 antenna lead
Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM
Philco model 60
I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM

[-]
Who's Online
There are currently 6846 online users. [Complete List]
» 2 Member(s) | 6844 Guest(s)
AvatarAvatar

>