1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Fogged clear
Warren
Senior Member
****
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
#17

07-01-2014, 04:09 PM
What does the nitrocellulose do for it? I have used th ebrushing laquer for spraying but it seems to come out with a rough finish. Maybe I just need to thin it more. You can sand it smooth , but would be nice if it was smoother after spraying. Was curious if the nitrocellulose had anything to do with it.
(This post was last modified: 07-01-2014, 04:09 PM by Warren.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Fogged clear - by Eric Adams - 06-29-2014, 10:17 PM
RE: Fogged clear - by Steve Davis - 06-29-2014, 10:56 PM
RE: Fogged clear - by Ron Ramirez - 06-30-2014, 05:38 AM
RE: Fogged clear - by Eric Adams - 06-30-2014, 08:49 AM
RE: Fogged clear - by morzh - 06-30-2014, 08:57 AM
RE: Fogged clear - by Ron Ramirez - 06-30-2014, 09:01 AM
RE: Fogged clear - by morzh - 06-30-2014, 10:54 AM
RE: Fogged clear - by Ron Ramirez - 06-30-2014, 11:33 AM
RE: Fogged clear - by Eric Adams - 06-30-2014, 11:43 AM
RE: Fogged clear - by bfrohwein - 06-30-2014, 12:21 PM
RE: Fogged clear - by Steve Davis - 06-30-2014, 01:19 PM
RE: Fogged clear - by Chuck Schwark - 06-30-2014, 01:45 PM
RE: Fogged clear - by Bob Andersen - 06-30-2014, 09:22 PM
RE: Fogged clear - by jerryhawthorne - 06-30-2014, 10:48 PM
RE: Fogged clear - by TA Forbes - 07-01-2014, 01:21 PM
RE: Fogged clear - by Bob Andersen - 07-01-2014, 02:13 PM
RE: Fogged clear - by Warren - 07-01-2014, 04:09 PM
RE: Fogged clear - by Steve Davis - 07-01-2014, 04:21 PM
RE: Fogged clear - by Bob Andersen - 07-01-2014, 05:47 PM
RE: Fogged clear - by Steve Davis - 07-01-2014, 06:41 PM
RE: Fogged clear - by Arran - 07-02-2014, 12:09 AM
RE: Fogged clear - by Bob Andersen - 07-02-2014, 12:56 AM
RE: Fogged clear - by jerryhawthorne - 07-02-2014, 01:05 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM
RCA 15X
Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM
Philco 91 Schematic
Hi Dan, I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration