Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 vs 650B
#3

Chuck,

Thanks for the suggestion. I did think about the possibility of cross-talk between the two radios in my original test set-up. So, I plugged the 650B into the isolated variac and operated the 90 directly from the AC line. That turned out to be a bad choice. I realize now that with such a short antenna, each receiver was using the AC line as the other half of the antenna.

So in my next test, I plugged both receivers into the AC line and I would tune in the same weak station on both. Then I unplugged one while the other was playing to eliminate the possibility of cross-talk or interference from the other, and vice-versa. So, operating both receivers one at a time both plugged directly into the AC line, the 650B was improved. With this set-up, I would say the 650B was at best on par with the 90, maybe just slightly less sensitive, but so close that one could easily say that could have been a difference in alignment or tracking across the band. Overall, you would have to say the sensitivity was about equal.

However, the 90 still had the 650B beat on selectivity. It is considerably sharper. You could easily tell when tuning in a weak station nearby a strong station. There was considerably less splatter on the 90 from the strong station.

Regards,

Ed


Messages In This Thread
Philco 90 vs 650B - by etech - 10-23-2008, 12:45 PM
Re: Philco 90 vs 650B - by Chuck Schwark - 10-23-2008, 01:05 PM
Re: Philco 90 vs 650B - by etech - 10-23-2008, 03:59 PM
Re: Philco 90 vs 650B - by Chuck Schwark - 10-23-2008, 04:36 PM
Re: Philco 90 vs 650B - by Ron Ramirez - 10-23-2008, 06:06 PM
Re: Philco 90 vs 650B - by etech - 10-23-2008, 06:16 PM
Re: Philco 90 vs 650B - by BDM - 10-24-2008, 11:20 AM
Re: Philco 90 vs 650B - by Chuck Schwark - 10-24-2008, 12:13 PM
Re: Philco 90 vs 650B - by BDM - 10-24-2008, 12:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Since these radios operated in harsh environments (temp changes and vibration) you could touch a soldering iron to all t...GarySP — 03:18 PM
6TPZ and 5TPO Radio Help
Thank you Gary. Hi Morzh. These radios are 6 transistor radios. Sadly no tubes. Thanks though.R3Sons — 02:19 PM
Heathkit Sweep Generator TS-4
Ron Instead of Quick reply, go to New Reply, then go to the title of the very first post, and change the title text the...morzh — 02:00 PM
6TPZ and 5TPO Radio Help
I am not a specialist in car radios. I suspect they might use vibrators to convert 12V to acceptable tube voltages, so ...morzh — 01:58 PM
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM

[-]
Who's Online
There are currently 6571 online users. [Complete List]
» 2 Member(s) | 6569 Guest(s)
AvatarAvatar

>