Starting on Philco 20 Deluxe.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Starting on Philco 20 Deluxe.

morzh
Odobenus rosmarus

Posts: 16,217
Threads: 562
Joined: Oct 2011
City: Jackson State, Province, Country: NJ

09-21-2014, 10:11 PM

Finished recap-recarb.
Would be it for testing, I have the filter block connected, though the can has not been cleaned yet but that is not needed for now.
However when starting on the chassis I saw the volume pot touched up, and I see the sectios have been swapped. The 250 Ohm section (the back one) is connected to GND and ANT, and the 5K section is biasing RF cathodes. The tell-tell sign, the GND strip is soldered to the back section. Should be the front one.

mañana....

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 11:52 AM

RE: Starting on Philco 20 Deluxe. - by Radioroslyn - 09-14-2014, 01:17 PM

RE: Starting on Philco 20 Deluxe. - by OldRestorer - 09-14-2014, 03:15 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 05:21 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 07:10 PM

RE: Starting on Philco 20 Deluxe. - by OldRestorer - 09-14-2014, 09:03 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-14-2014, 09:27 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-21-2014, 10:11 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-23-2014, 09:10 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 09-25-2014, 12:05 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 10-15-2014, 11:01 PM

RE: Starting on Philco 20 Deluxe. - by Arran - 10-16-2014, 12:51 AM

RE: Starting on Philco 20 Deluxe. - by morzh - 10-16-2014, 11:50 AM

RE: Starting on Philco 20 Deluxe. - by morzh - 10-16-2014, 10:54 PM

RE: Starting on Philco 20 Deluxe. - by Ron Ramirez - 10-17-2014, 01:44 PM

RE: Starting on Philco 20 Deluxe. - by morzh - 10-17-2014, 04:00 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM

Who's Online

There are currently 9043 online users. [Complete List]
» 2 Member(s) | 9041 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me