Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Feeling the current ....
#12

Mike

Human capacitance varies with surroundings but typically is estimated to be within few tens to a couple of hundreds of pF which is very, very low, the human ESDA body model being 100pF+1.5kOhm.

Obviously when one stands close to a large metal grounded object like a fridge or something, or a slab foundation (or basement floor) close to Earth surface the capacitance will somewhat increase, but at 60Hz you have to have about 20nF capacitance to start feeling the current (1mA AC or so).

Which is why I asked where the radio is situated. Because while operating a truly Hot Chassis models (the two I did for Kirk) without knobs and plugged directly into Mains in my house on the second floor, I did not feel squat while tuning or turning on the radio, not before or after it was turned on.


Messages In This Thread
Feeling the current .... - by ODPILOT - 11-09-2014, 07:50 PM
RE: Feeling the current .... - by Mondial - 11-09-2014, 08:22 PM
RE: Feeling the current .... - by morzh - 11-09-2014, 08:42 PM
RE: Feeling the current .... - by ODPILOT - 11-09-2014, 09:13 PM
RE: Feeling the current .... - by Arran - 11-10-2014, 01:31 AM
RE: Feeling the current .... - by morzh - 11-10-2014, 10:15 AM
RE: Feeling the current .... - by ODPILOT - 11-10-2014, 09:22 PM
RE: Feeling the current .... - by ODPILOT - 11-10-2014, 09:24 PM
RE: Feeling the current .... - by morzh - 11-10-2014, 11:33 PM
RE: Feeling the current .... - by mikethedruid - 11-11-2014, 06:17 AM
RE: Feeling the current .... - by PAradiogeek - 11-11-2014, 07:36 AM
RE: Feeling the current .... - by morzh - 11-11-2014, 12:16 PM
RE: Feeling the current .... - by ODPILOT - 11-11-2014, 02:17 PM
RE: Feeling the current .... - by morzh - 11-11-2014, 02:32 PM
RE: Feeling the current .... - by ODPILOT - 11-12-2014, 07:24 PM
RE: Feeling the current .... - by morzh - 11-12-2014, 08:00 PM
RE: Feeling the current .... - by Arran - 11-14-2014, 03:25 AM
RE: Feeling the current .... - by codefox1 - 11-15-2014, 04:39 PM
RE: Feeling the current .... - by morzh - 11-15-2014, 05:16 PM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently no members online.

>