1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
New here, an 89B I'm repairing
morzh
Odobenus rosmarus
******
Posts: 16,217
Threads: 562
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#11

12-01-2014, 04:38 PM
How do you know it is not oscillating?
Did you try another radio tuned to the same frequency or else?

Ron as I remember had to go all the way down to 7,500 Ohm with that resistor.
I believe he also reccommends baking the coil.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
New here, an 89B I'm repairing - by sparkydave - 06-20-2014, 08:45 PM
RE: New here, an 89B I'm repairing - by Mondial - 06-20-2014, 09:47 PM
RE: New here, an 89B I'm repairing - by gregb - 06-20-2014, 09:49 PM
RE: New here, an 89B I'm repairing - by morzh - 12-01-2014, 04:38 PM
RE: New here, an 89B I'm repairing - by AI2V - 12-01-2014, 06:12 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM

[-]
Who's Online
There are currently 4591 online users. [Complete List]
» 2 Member(s) | 4589 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration