1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Vernier shaft repair
dixierat
Junior Member
**
Posts: 49
Threads: 8
Joined: Nov 2008
City: Baton Rouge, LA
#5

01-20-2009, 10:19 PM
OK thanks for resolving the little ball issue, it is not attached to the vernier shaft. Now I need to straighten the brass pinion shaft. My initial thoughts on how to do this would be to place a flat steel strip on the bow and gently hammer it straight.As I have no experience straightening shafts would appreciate comments from knowledgeable restorers.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Vernier shaft repair - by dixierat - 01-19-2009, 09:48 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 05:10 AM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 08:14 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 09:35 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 10:19 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:03 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 11:35 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 11:40 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:54 PM
Re: Vernier shaft repair - by dixierat - 01-21-2009, 11:16 PM
Re: Vernier shaft repair - by Texasrocker - 01-22-2009, 12:30 AM
Re: Vernier shaft repair - by exray - 01-22-2009, 06:36 AM
Re: Vernier shaft repair - by dixierat - 01-22-2009, 08:43 PM
Re: Vernier shaft repair - by Texasrocker - 01-23-2009, 03:53 AM
Re: Vernier shaft repair - by dixierat - 01-23-2009, 10:03 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM
B&K 1077B no video
I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM
RCA 15X
I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM
B&K 1077B no video
Hello Tim, I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!. Sincerely...radiorich — 11:07 PM

[-]
Who's Online
There are currently 10345 online users. [Complete List]
» 1 Member(s) | 10344 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration