Bakelite block challenge???

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Bakelite block challenge???

klondike98
Phorum Moderator

Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

#6

04-21-2015, 09:21 PM

Dan, I'm on my phone so answering this is a little cumbersome...hope ive got my info right. You have a 3650 which is the Canadian version of US 650 (schematic link). Looking at block cap #80 it does say 0.3uF That probably means the two 0.15uF caps in the block are wired in parallel to yield 0.3uF value. can you show a close up photo on the block#80?

The "U" means that pin 1 is ungrounded. I suspect that pins 2 & 3 are wired together with a jumper wire?? Which gives the 0.3uF cap value. Make sense?

[in your previous post I think you mean to have written 0.3uF and 0.15uF where you have written .03 and .05....]

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

« Next Oldest | Next Newest »

Messages In This Thread

Bakelite block challenge??? - by Dan Walker - 04-21-2015, 05:07 PM

RE: Bakelite block challenge??? - by radiohenry - 04-21-2015, 07:12 PM

RE: Bakelite block challenge??? - by sam - 04-21-2015, 07:16 PM

RE: Bakelite block challenge??? - by klondike98 - 04-21-2015, 07:24 PM

RE: Bakelite block challenge??? - by Dan Walker - 04-21-2015, 08:44 PM

RE: Bakelite block challenge??? - by klondike98 - 04-21-2015, 09:21 PM

RE: Bakelite block challenge??? - by Dan Walker - 04-23-2015, 09:45 AM

RE: Bakelite block challenge??? - by morzh - 04-23-2015, 10:52 AM

RE: Bakelite block challenge??? - by klondike98 - 04-23-2015, 12:29 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

Who's Online
There are currently no members online.