Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-1012 Alignment
#17

Yup, the radios, their components, and their caretakers are just getting older every day.

I've been replacing carbon resistors as a matter of course in a restoration for several years now. In recent years, I've started automatically replacing common value micas (100 pF, 250 pF) as well.

I think this problem will only get worse over time...

"Keep 'em Flying" Icon_wink

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco 42-1012 Alignment - by vecher - 04-22-2015, 08:40 PM
RE: Philco 42-1012 Alignment - by Radioroslyn - 04-22-2015, 09:00 PM
RE: Philco 42-1012 Alignment - by Nick3092 - 04-22-2015, 09:28 PM
RE: Philco 42-1012 Alignment - by vecher - 04-22-2015, 11:03 PM
RE: Philco 42-1012 Alignment - by vecher - 04-24-2015, 02:44 PM
RE: [b]Philco 42-1012 Alignment[/b] - by vecher - 04-25-2015, 11:16 PM
RE: Philco 42-1012 Alignment - by vecher - 04-26-2015, 04:01 PM
RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-27-2015, 12:34 PM
RE: Philco 42-1012 Alignment - by klondike98 - 04-27-2015, 03:30 PM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 03:59 PM
RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 06:59 PM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 08:06 PM
RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 08:36 PM
RE: Philco 42-1012 Alignment - by vecher - 04-29-2015, 12:50 AM
RE: Philco 42-1012 Alignment - by klondike98 - 04-29-2015, 08:35 AM
RE: Philco 42-1012 Alignment - by Eliot Ness - 04-29-2015, 10:16 AM
RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-29-2015, 11:08 AM
RE: Philco 42-1012 Alignment - by sleuth255 - 04-29-2015, 02:24 PM
RE: Philco 42-1012 Alignment - by codefox1 - 04-29-2015, 03:09 PM
RE: Philco 42-1012 Alignment - by vecher - 04-30-2015, 10:51 PM
RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:17 AM
RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 11:27 AM
RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:45 AM
RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 04:43 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM

[-]
Who's Online
There are currently 4506 online users. [Complete List]
» 2 Member(s) | 4504 Guest(s)
AvatarAvatar

>