Philco 42-1012 Alignment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 42-1012 Alignment

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#22

05-11-2015, 11:27 AM

I had them on hand. Normally you do not have to replace Mica Caps. But looks like these old radios some if not all of the caps drift. Do you have a capacitor meter? easier to check caps around your Osc tube then trying to replace all of them.. Mine were way out of spec..

Skip...

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 42-1012 Alignment - by vecher - 04-22-2015, 08:40 PM

RE: Philco 42-1012 Alignment - by Radioroslyn - 04-22-2015, 09:00 PM

RE: Philco 42-1012 Alignment - by Nick3092 - 04-22-2015, 09:28 PM

RE: Philco 42-1012 Alignment - by vecher - 04-22-2015, 11:03 PM

RE: Philco 42-1012 Alignment - by vecher - 04-24-2015, 02:44 PM

RE: [b]Philco 42-1012 Alignment[/b] - by vecher - 04-25-2015, 11:16 PM

RE: Philco 42-1012 Alignment - by vecher - 04-26-2015, 04:01 PM

RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-27-2015, 12:34 PM

RE: Philco 42-1012 Alignment - by klondike98 - 04-27-2015, 03:30 PM

RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 03:59 PM

RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 06:59 PM

RE: Philco 42-1012 Alignment - by Eliot Ness - 04-27-2015, 08:06 PM

RE: Philco 42-1012 Alignment - by vecher - 04-27-2015, 08:36 PM

RE: Philco 42-1012 Alignment - by vecher - 04-29-2015, 12:50 AM

RE: Philco 42-1012 Alignment - by klondike98 - 04-29-2015, 08:35 AM

RE: Philco 42-1012 Alignment - by Eliot Ness - 04-29-2015, 10:16 AM

RE: Philco 42-1012 Alignment - by Ron Ramirez - 04-29-2015, 11:08 AM

RE: Philco 42-1012 Alignment - by sleuth255 - 04-29-2015, 02:24 PM

RE: Philco 42-1012 Alignment - by codefox1 - 04-29-2015, 03:09 PM

RE: Philco 42-1012 Alignment - by vecher - 04-30-2015, 10:51 PM

RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:17 AM

RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 11:27 AM

RE: Philco 42-1012 Alignment - by Edisla - 05-11-2015, 11:45 AM

RE: Philco 42-1012 Alignment - by vecher - 05-11-2015, 04:43 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM

Who's Online

There are currently 5880 online users. [Complete List]
» 1 Member(s) | 5879 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me