42-1008P ALigntment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

42-1008P ALigntment

Edisla
Member

Posts: 155
Threads: 25
Joined: Sep 2014
City: Folsom, CA

05-11-2015, 11:57 PM

Ok here is what I see comparing schem to actual parts

Schem / actual part

(4) 250uuF / 600uuF (BL,BK,BN)

(5) 360uuF / 046uuF (BK,Y, BL)

(10) 10uuF / 10uuf (BN, BK, BK)

(12) 680ohm / 1k and found it tucked behind and right on the Osc. coil terminals

(13) 325uuF / 32uuF (BK, O, R)

(16) 300uuF / 300uuF (O, BK, BN)

(20) 250uuF \ 600uuF (BL,BK,BN)

(24) 250uuF / 250uuF (R, BK, BN)

From what it looks like these appear to be original from what it looks like anyway. (5) and (13) I'm not 100% on, hard to get to and values of what I am getting from the color codes seem odd???

(This post was last modified: 05-11-2015, 11:58 PM by Edisla.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

42-1008P ALigntment - by Edisla - 05-10-2015, 11:58 PM

RE: 42-1008P ALigntment - by Warren - 05-11-2015, 12:07 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 09:54 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 10:43 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:29 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 01:25 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 09:56 PM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:31 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 11:57 PM

RE: 42-1008P ALigntment - by Edisla - 05-12-2015, 12:48 AM

RE: 42-1008P ALigntment - by Nick3092 - 05-12-2015, 10:09 AM

RE: 42-1008P ALigntment - by vecher - 05-18-2015, 11:36 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 09:48 PM

RE: 42-1008P ALigntment - by Ron Ramirez - 05-20-2015, 09:59 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 10:23 PM

RE: 42-1008P ALigntment - by vecher - 05-20-2015, 10:32 PM

RE: 42-1008P ALigntment - by Edisla - 05-21-2015, 11:41 AM

RE: 42-1008P ALigntment - by vecher - 05-21-2015, 09:18 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM
6TPZ and 5TPO Radio Help
Oh...and you have electrolytic caps there. All need to go and be replaced.morzh — 04:36 PM
6TPZ and 5TPO Radio Help
Thanks, will do.R3Sons — 01:25 PM
1930s Stewart-Warner Tombstone Radio need help identifying model number
UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM
Philco 91 Schematic
Hi Rod, The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM
Just got a 49-1613 need to know...everything!
I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM
B&K 1077B no video
Hello Tim, I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ? Sincerely Richardradiorich — 01:55 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me