Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Persistance Pays Off!
#8

More good news with this radio. Tested the tubes and all were very good except the 7B8 tube which read a bit weak. Luckily, I had a better 'Genuine Philco' 7B8 in my stash to swap into the radio. I must say, these loktals are fairly durable tubes overall. Both dial bulbs are blown, but everything else checks out so far. One question I have is cleaning the slug tuners on these units. As I said earlier, it will tune some stations on low power, but it's VERY touchy and I am suspecting dirt and crap in the tuner. Is there a safe way to clean these or should I simply use compressed air to get the worst of the gunk out of the tuning coils and slugs?

No matter where you go, there you are.


Messages In This Thread
Persistance Pays Off! - by Jayce - 07-25-2015, 07:22 PM
RE: Persistance Pays Off! - by NostalgiaRadioTime - 07-25-2015, 09:07 PM
RE: Persistance Pays Off! - by Jayce - 07-25-2015, 09:16 PM
RE: Persistance Pays Off! - by NostalgiaRadioTime - 07-25-2015, 09:26 PM
RE: Persistance Pays Off! - by VntgRads - 07-25-2015, 09:53 PM
RE: Persistance Pays Off! - by Jayce - 07-25-2015, 10:06 PM
RE: Persistance Pays Off! - by Squire - 07-26-2015, 11:59 AM
RE: Persistance Pays Off! - by Jayce - 07-27-2015, 04:01 PM
RE: Persistance Pays Off! - by Scottb - 07-28-2015, 10:01 AM
RE: Persistance Pays Off! - by Arran - 07-29-2015, 06:26 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New member
Hello jeff, Welcome aboard ! Sincerely Riochardradiorich — 06:53 PM
New member
Good picture, When was it taken? You don't look in it like a guy who has a teenage son :)morzh — 06:13 PM
New member
Love the pic! I'm southern IL, so wouldn't be much help and Bob Anderson is very good on those, but lives in Chicago are...TV MAN — 05:25 PM
Philco 40-120C Filament Wiring
:thumbup:klondike98 — 04:56 PM
Philco 40-120C Filament Wiring
With these values I think you are OK; the Cmax for this tube is 40uF. Your Vbb could rise a bit, but probably not too mu...morzh — 04:53 PM
Philco 40-120C Filament Wiring
BTW, someone had replaced the original 20uF/20uF filter cap with a 47uF/33uF cap. Do you think these values are safe on ...bluecap — 04:33 PM
Philco 40-120C Filament Wiring
You're correct. I was misinterpreting the key position. I now know where it is, and things are making sense. I appreciat...bluecap — 04:29 PM
Philco 40-120C Filament Wiring
I think Morzh has a good thought. Check the key position. The under chassis diagram in the Philco info shows an “H” for ...klondike98 — 04:25 PM
Philco 630csx power cord
Yes, the third wire goes to the stud on the side and is separate from the other two. I've usually used cloth covered ...Tynwald — 03:09 PM
New member
Have you tried Alabama Historical Radio Society? They possibly could recommend someone. I remember a name of Dee Hanes...morzh — 03:08 PM

[-]
Who's Online
There are currently 4825 online users. [Complete List]
» 3 Member(s) | 4822 Guest(s)
AvatarAvatarAvatar

>