1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
my 37-61 the work...
mikethedruid
Banned
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
#2

10-09-2015, 11:30 AM
Well, I applied the Re-Faux Pro decals. I found that they do not quite align with my cabinet, the pattern printed on them was just a little bit too large, I think. It looks a bit better than it did, but that is about all that can be said of it. I have written Tony, to see what I can do about it. I figure I will have to re-do it at the very least, but unless I can get a set of decals that align better than these, I don't see much point. Here are pictures to show you what I mean. Be sure to look at the picture in the post above to see how things aligned originally.

[Image: http://40.media.tumblr.com/fbc013e2d4623...1_1280.jpg]

[Image: http://41.media.tumblr.com/feb231fc20086...2_1280.jpg]

[Image: http://41.media.tumblr.com/d166a5d77f267...3_1280.jpg]

[Image: http://41.media.tumblr.com/c7fb2a483b8ec...4_1280.jpg]

I have written Tony and sent him these pictures to document my problem. I'm not sure if there is a solution. Stay tuned for further details...
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
my 37-61 the work... - by mikethedruid - 09-27-2015, 04:00 PM
RE: my 37-61 the work... - by mikethedruid - 10-09-2015, 11:30 AM
RE: my 37-61 the work... - by OldRestorer - 10-09-2015, 11:53 AM
RE: my 37-61 the work... - by mikethedruid - 10-09-2015, 12:18 PM
RE: my 37-61 the work... - by mikethedruid - 10-11-2015, 04:58 PM
RE: my 37-61 the work... - by Ron Ramirez - 10-12-2015, 03:58 PM
RE: my 37-61 the work... - by mikethedruid - 10-13-2015, 04:50 AM
RE: my 37-61 the work... - by mikethedruid - 10-13-2015, 04:12 PM
RE: my 37-61 the work... - by mikethedruid - 12-10-2015, 06:46 PM
RE: my 37-61 the work... - by sam - 12-10-2015, 08:08 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Restore Code ??
Or you could just square the current :lol: As for the values, they are dependent on the 1 or 2-speaker system. The...morzh — 05:46 PM
Philco 91 Restore Code ??
If you know the fc resistance you can use 120 ma nominal current through the resistor to get the voltage drop then calcu...RodB — 05:21 PM
Philco 91 Restore Code ??
Thanks Mike. I at least know why it is there if I don't fully understand it. I see where you talk about a cap and resist...dconant — 04:49 PM
Philco 91 Restore Code ??
Well, this cap you showed cannot possibly, due to the way it is constructed, be 1000pF (0.001). It can be in tens of pF....morzh — 03:13 PM
Philco 91 Restore Code ??
I have two schematics for this radio one shows the 47 block (126-226) and the other (121-221) does not. My radio does no...dconant — 02:32 PM
Philco 91 Restore Code ??
No, that cannot be the 47. The 47 is a regular backelite block cap. Look at the chassis picture, it is shown there. Rig...morzh — 01:45 PM
Philco 91 Restore Code ??
I have changed the title of this thread from Philco 91 Schematic. I have gone through most of the cap replacements. I...dconant — 01:26 PM
462ron
Here is an online transistor substitution site… Ron462ron — 08:44 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a &quo...captainclock1988 — 12:55 AM
B&K 1077B no video
Hello Tim, I once had a Jcpenny 13inch tv /monitor built by NEC come into my repairshop it would start acting up at tim...radiorich — 10:59 PM

[-]
Who's Online
There are currently 3280 online users. [Complete List]
» 4 Member(s) | 3276 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration