my 37-61 project...

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

my 37-61 project...

~~mikethedruid~~
Banned

Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN

11-17-2015, 12:51 AM

Actually, I figure I REALLY only need 2 watt for the 202 ohm section, the 8 ohm section and the 35 ohm section could be 1/2 watt, which, of course, would be a cost saving. Again, using I squared R. Looking at the schematic for the 37-60, it used the same bias resistor. What have others used here ? As I said, advice appreciated before I plunge ahead.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

my 37-61 project... - by mikethedruid - 09-26-2015, 05:12 PM

RE: my 37-61 project... - by mikethedruid - 09-30-2015, 04:29 PM

RE: my 37-61 project... - by mikethedruid - 10-02-2015, 06:44 PM

RE: my 37-61 project... - by mikethedruid - 10-05-2015, 07:40 PM

RE: my 37-61 project... - by mikethedruid - 10-17-2015, 01:03 PM

RE: my 37-61 project... - by KCMike - 10-17-2015, 01:56 PM

RE: my 37-61 project... - by mikethedruid - 10-17-2015, 02:53 PM

RE: my 37-61 project... - by mikethedruid - 11-16-2015, 08:23 PM

RE: my 37-61 project... - by mikethedruid - 11-17-2015, 12:51 AM

RE: my 37-61 project... - by klondike98 - 11-17-2015, 01:46 AM

RE: my 37-61 project... - by mikethedruid - 11-17-2015, 03:06 AM

RE: my 37-61 project... - by mikethedruid - 12-09-2015, 10:08 PM

RE: my 37-61 project... - by kiwi_steve - 12-10-2015, 01:07 AM

RE: my 37-61 project... - by mikethedruid - 12-11-2015, 09:38 AM

RE: my 37-61 project... - by mikethedruid - 12-13-2015, 12:10 AM

RE: my 37-61 project... - by mikethedruid - 12-14-2015, 08:38 PM

RE: my 37-61 project... - by mikethedruid - 12-27-2015, 08:22 PM

RE: my 37-61 project... - by mikethedruid - 12-27-2015, 11:38 PM

RE: my 37-61 project... - by mikethedruid - 12-28-2015, 01:53 AM

RE: my 37-61 project... - by klondike98 - 12-28-2015, 10:20 AM

RE: my 37-61 project... - by mikethedruid - 01-01-2016, 01:53 AM

RE: my 37-61 project... - by mikethedruid - 01-27-2016, 03:58 PM

RE: my 37-61 project... - by KCMike - 01-27-2016, 05:35 PM

View a Printable Version

Users browsing this thread: 8 Guest(s)

Recent Posts
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being o...morzh — 05:13 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake :think: ) X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me