1935 Philco model 89 restore on YouTube
Posts: 1,532
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Buzz,
Go here: http://philcorepairbench.com/bblokcap.htm
Scroll down to Bakelite Block #4989-H and you'll see which tabs on the bakelite block the twin .09's are connected to.
I remember this from my model 89, code 123 (pictured as my profile avatar).
Greg V.
West Bend, WI
Member WARCI.org
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Hi Greg..My block is printed with a 4989-AH has 3 lugs on it and had 3 wires coming up from it.......I guess my real question is, if there are two .09 caps in that block, the schematic shows #5 block with only one .09 with a 300 ohm cap in parallel...where is the other one?.....one wire goes to the antenna coil, and the other goes to a 1mg resistor...I'm confused, and am calling it a night...thanks, Buzz
Posts: 1,532
Threads: 242
Joined: Sep 2012
City: West Bend, Wisconsin
Doing a little further investigation, block 4989-AH was later replaced with 4989-ODG, which had two .1 caps inside. That block is listed on the page I linked to above (scroll a bit further down the page). Basically, one end of each of the two caps go to the ground terminal, and the other ends go to terminal 2 and terminal 3 (making the three connections you see coming up). As to the why it only shows one cap on the schematic, possibly it was a revision they missed making in print? Who knows for sure what they were thinking 83 years ago.
Greg V.
West Bend, WI
Member WARCI.org
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Hello...this is for anybody to answer or anybody who can help.......On the Philco 89 radio with a 36 tube, with the police band.....what is your source for the numbering of the parts that's on the schematic?
I am talking about a part location diagram with the part number in a circle.......just curious, I was using a Model 19 and 89 source. Is there anything else newer than this one, besides the Philco 89 Code 123 schematic that uses the 77 oscillator tube???.....Buzz
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Did you read the link I posted previously?
--
Ron Ramirez
Ferdinand IN
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Ron.....I saw your link with the various schematics..but what is your master list for the parts locations diagram at?
Buzz
(This post was last modified: 02-27-2017, 10:52 PM by Buzz.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
The only parts lists ever published were in the original Bulletin 146 (models 89 and 19, code 121) and Bulletin 146-B (model 89, code 123, 77 tube). This is why I wrote the "Evolution" article which was formerly on my website and is now part of the Phorum - Philco changed the 89 so many times over the years, and usually only documented the changes by minor mentions in various "Changes in Models" bulletins issued sporadically. And to top it all off, not all changes were documented.
So...you have to do the best you can with the information available. The "Evolution" article is the most comprehensive information available on model 89.
And...if you're good at reading schematics and transposing what is on the schematic to what is under the radio's chassis, you don't need a parts list...
--
Ron Ramirez
Ferdinand IN
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Ron.. I'm trying to figure out why my radio is wired different than the schematics you posted.. If you're using the model 19 and 89 parts replacement list, then for example, #5 cap block which your list as a dual .09's ..is located in the wrong place..the schematic has the .09's from the #7 five part condenser can mixed up with the twin 09's in block #5......according to my wiring ....did someone rewire my radio..I don't think so.......it works....Buzz
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Again...poor to no documentation...one gets used to it after awhile...it's a Philco thing...
Yes, it is too bad that Philco did not document like RCA, even going to the lengths of putting together a comprehensive under-chassis wiring diagram which showed not only where parts were located, but how they were wired together. But Philco did not do this. RCA had plenty of money, so they could afford to pay someone to do that. Philco - in the 1930s at least - focused on going as far as they could at the lowest possible cost. One result was the poor documentation of their products.
Post a photo of the underside of your chassis, let us see what it looks like.
--
Ron Ramirez
Ferdinand IN
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
https://www.flickr.com/photos/147665380@...res/F2GXsg
https://www.flickr.com/photos/147665380@...res/01YAfE
This is how my Model is wired. On the first picture you can see the arrow pointing to Bakelite block #5
and the other arrow pointing to #7 capacitor can.
The photo clearly shows block #5 (twin 09's) going to the antenna coil (#2 on parts layout)
and the other going to the junction of #41 and #42 (99,000K and 1 Mg resistors)
So, either the schematic is wrong or mis-numbered, or my radio was re-wired. Can anyone who has this model check theirs?
The 5 wires coming out of the can are marked by scotch tape,, The two .09's from the can show the wires going
to pins 3 and 4 of the RF Tube socket (bottom right)...also different from the schematic numbering.
Now, does this really matter?... probably not.... but if people are locating their parts off the parts layout sheet,
it can get confusing......Buzz
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Interesting.
In your photos, I do not see a separate 300 ohm resistor between the 36 RF amp cathode and ground (looks like a short cloth-covered wire with tubular terminals and regular wires on each end).
Resistor (10) is hidden under the large 5,000 ohm resistor (20) which is under your (7E - .05) tape tag, so I cannot see if it is 15K or 10K.
Regardless...I'm seeing enough wiring oddities that I would need to compare yours to another 89 of the same vintage...and I do not own one. I have an 89-121, the early AM-only version as well as a late 1936 89-123 with 77 tube. Nothing in between. Someone else with an 89 like yours is going to have to jump in here.
--
Ron Ramirez
Ferdinand IN
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
The 300 0hm resistor is one of those flexible resistors that looks like cloth wire and it is going from pin 4 of the RF to ground. and is also covered with additional black cloth so you cant see it.
#10 has a 15K resistor installed
Buzz
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Hello:
Part 2 of the Philco series is now uploaded
link below for anyone interested
https://www.youtube.com/watch?v=FVSBAq9bBOA&t=1141s
(This post was last modified: 03-10-2017, 02:58 PM by Buzz.)
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Hello:
Part 3 of the Philco series is now uploaded
link below for anyone interested
https://www.youtube.com/watch?v=UejJCxfOeFo
(This post was last modified: 03-17-2017, 05:43 PM by Buzz.)
Posts: 362
Threads: 60
Joined: Jan 2013
City: Portland, Oregon
Users browsing this thread: 4 Guest(s)
|
|
Recent Posts
|
|
RCA T62 is playing.....
|
| Beautiful set.morzh — 09:07 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Well....here it is.
The green stuff. Unfortunately, probably penetrates deep.
I opened the top layer and saw that:
...morzh — 08:58 PM |
|
Philco 91 Restore Code ??
|
| :clap: :clap: :clap: :clap:
Really nice workmanship!!! Top of the chassis looks great.
Sorry about the long winded e...MrFixr55 — 08:09 PM |
|
Philco 40-120C Restoration
|
| Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM |
|
RCA T62 is playing.....
|
| Nice looking set great save. DavidDavid — 07:48 PM |
|
Philco 89 indicator light.
|
| Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| MrFixr
Yes, it is my plan to go with 45rpm spider if I go that far.
No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM |
|
Philco 40-120C Restoration
|
| Change the tube. Check the tube's bias network.
Are any other tubes experience the drop or just this?`
Is resistor 23 OK...morzh — 07:09 PM |
|
Philco 89 indicator light.
|
| I forgot how the pointer is formed: could you show the way it is formed and how you tried to change it?morzh — 07:01 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Was that pole piece left handed ?
Since the metal "spider" is toast, wonder if you can either get the "4...MrFixr55 — 06:54 PM |
|
Who's Online
|
There are currently 8421 online users. [Complete List]
» 3 Member(s) | 8418 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
