Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 speaker
#1

hey guys
I have a 38-116 speaker.  cone has small tear other then that great
NO   voice coil on cone bad thought rewire it ?
has any one had luck trying to get paper cone off speaker frame
with out tearing it ?

thanks sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#2

Some of the spkr cones are held down with sheet metal screws along the perimeter. If not you'll have to use a solvent like acetone or mek to remove the adhesive. Start small by wetting edge and work your way around slowly. So do you have the chassis and cabinet too??

Have you tried to measure the resistance of the vc as close the coil as you can eliminating the possibility of a bad connection or bad hb coil?

Terry
#3

Ed Locker showed me how to use acetone to remove speaker cones in this manner several years ago. The trick is not to use too much acetone...just a little from a dropper is the preferred way to apply it...and be patient as it may take more than one application of acetone.

--
Ron Ramirez
Ferdinand IN
#4

 Terry
I tried testing bottom of cone where winding is but get nothing 
I see 1 coil wire on right but don't see a wire on left
Should have some continuity.  I Ohmed out green and white wires
Going to it. Has .05 ohms  
Did get cone screw out and disk up just have to remove cone 
I have to also look for cabinet 
Little miss happen a work with it 
Sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#5

Hey Sammy,
I know a old guy who is a real pita that has a spkr from a 37-116. It does have some paper damage but he thinks it's serviceable. Now a nice young clean cut guy like you could probably have it if this old fart can find it.

Terry
#6

lol Icon_lol
I seen that old fart`s house he`ll never find it Icon_shh

not kirk

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
1 - 0v - correct 2 - 0v - correct 3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being o...morzh — 05:15 PM
B&K 1077B no video
I'm going to get back into it tonight. but I disconnected the 2 main resistors off this supply going to different parts ...TV MAN — 04:04 PM
6TPZ and 5TPO Radio Help
Sorry. The test points are as follows: 1 - 0v 2 - 0v 3 - 0v 4 - 12v 5 - 0v 6 - 11.9v 7 - 12v 8 - 12v 9 - 12v...R3Sons — 02:09 PM
6TPZ and 5TPO Radio Help
OK, so 18 and 19 as they should be. What is "everything else?" Try to be more specific in your descriptions:...morzh — 12:44 PM
6TPZ and 5TPO Radio Help
Yeah, I'm still on 5TPO. Sorry, my bad, points 1 and 2 should be points 18 and 19 (easy mistake  :think: )  X7 is shown ...R3Sons — 11:42 AM
Philco 40-120C Filament Wiring
Hi folks, I'm in the process of restoring a Philco 40-120C and I'm finding the wiring to be a bit puzzling. According to...bluecap — 11:28 AM
462ron
Hi Levi, here’s just a thought. Most radios run the oscillator higher than the dial setting. Say you set your radio to 1...462ron — 10:10 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
Another Update: I found a couple of damaged coils inside this radio that might have something to do with why this radio ...captainclock1988 — 10:51 PM
6TPZ and 5TPO Radio Help
If you are still on 5TPO, you lost me there. What X7? What Points 1 and 2?morzh — 08:37 PM
6TPZ and 5TPO Radio Help
Quick progress report: X7 is broken. Only one leg soldered, the other missing and the diode is cracked. I've replaced...R3Sons — 05:05 PM

[-]
Who's Online
There are currently no members online.

>