Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PHILCO 296 Model H Speaker Question
#1

Please forgive my ignorance in advance. I have picked up a Philco 296 which I am in the earliest stages of learning to restore. The first and most obvious problem is the speaker is trashed. The paper is gone and the center voice coil is trashed. The speaker is a Model H, but can it be replaced with another Model? I have learned that the Model H is a 3200 Ohm speak operating at 40ma.(I think...) Is there another Philco speaker that I can replace this one. I see a Model G on EBAY with the same plug, but I am not sure if this would work. I have much to learn. Any suggestions? Thank you for any help.

Frank
#2

Hi Frank and welcome,
Have a look here   http://philcoradio.com/phorum/showthread.php?tid=215  Find spk zip and click on it. There you will find specs for all of the Philco speakers. Looks like there are 4 or 5 that use the same cone/voice coil assembly including the G and H models.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!
Icon_wave
#4

Thank you so much! I will go ahead and order the Model G and see where I am at. This will at least get me going. It may need to be re-coned and cleaned up, but perhaps this will at least get some sound.  The chassis is dirty but it looks like it has been recapped a long time ago and serviced several times over the years based upon on the dates and signatures. I have power to all the tubes so one step at a time. Thank you again and I may be back with several more questions.  Icon_wtf
#5

Thank you for having me. I am glad that I found this forum. I not afraid to learn, but I will admit that I am walking in the woods blind at this point. lol
#6

Have patience and you will be rewarded Icon_smile

Welcome.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Terry and Mike will get you through it, have no fear. If you're an ace at reading schematics you're better off than I was a few months ago.

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM
An attempt to remove the Field Coil from a G speaker
Mike, give this site a look for your spider. Can't hurt. Take care and BE HEALTHY! -GaryGarySP — 12:41 PM
An attempt to remove the Field Coil from a G speaker
Rod, Bubble packaging? The one I know (if you mean the large bubble type) is really thin. I have some at home. Is there...morzh — 12:23 PM
An attempt to remove the Field Coil from a G speaker
Q8. What's the meaning of life? I have read that someone made a spider out of the clear plastic from bubble packagin...RodB — 11:07 AM
An attempt to remove the Field Coil from a G speaker
So, Q1. Does anyone know where to get the spider. Q2. If there is no such place, what material is best? I doubt tin is...morzh — 09:43 PM
An attempt to remove the Field Coil from a G speaker
Arran The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM

[-]
Who's Online
There are currently 8081 online users. [Complete List]
» 1 Member(s) | 8080 Guest(s)
Avatar

>