Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 44B clamshell cathedral
#1

Hi folks,

Here is my newest acquisition.  Can you all help me date this 44B?  I don't see it in the photo gallery.  It uses a different cabinet than the two other 44Bs I have seen.  What year is it?  

I have heard it called a clamshell cathedral.  Anyone have a different name?

It is different from the 144B clamshell I have.  Different escutcheon and knobs.   

It seems to fit the "Philco for 1935 (June 1934)" category era.  Am I right?

Ron?


Attached Files Image(s)
           
#2

It's a 144B, but the escutcheon isn't right? I wonder if it is a very early production model that used a leftover 1933-34 Model 16 escutcheon?

--
Ron Ramirez
Ferdinand IN
#3

Replaced Escutcheon. You can actually see the other escutcheon outline behind the new escutcheon..


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Wow, good eye, Kirk. I still don't see it.

Which would mean that, someone also put the wrong knobs on it as well.

--
Ron Ramirez
Ferdinand IN
#5

Huh.  Maybe it's my bad photography.  I realized it is the pretty much the same at the 144B clamshell I have at home.  The left one what I just found and is at my office.  (I know, I should bring it home and compare...)

The stitched together photo shows the two and their differences.

I've noticed on the left one has a layer of what may be tar from cigarettes, cigars on the face of the cabinet.  Maybe it's just old and has a lot of wear on the finish.  Check out the tuning knob - a lot of wear around it  The knobs and escutcheon are different than the other 144B. 

Maybe they were switched out... or, did Philco vary the escutcheon and knobs on this model to suit the taste of the buyer?  The escutcheon sure looks original to me...

Could the rosette knobs indicate a 44B and the hex knobs a 144B?  What do you all think?


Attached Files Image(s)
   
#6

END of the RUN,,,ran out,,,used NEW stuff ????
#7

I suggest you carefully remove the escutcheon, take some close-up photos of the hole where the escutcheon mounts, and post them here. That will allow me to tell you whether or not it left the factory with the older escutcheon.

--
Ron Ramirez
Ferdinand IN
#8

Sounds good Ron. I will post pictures when I do so. Thanks!
#9

Okay, here are the pictures with the escutcheon removed.  

Was it factory or customer/collector???

The cuts in the cabinet to fit this particular escutcheon are not fresh. It was done some time ago.


Attached Files Image(s)
       
#10

There's your answer - some "collector" took a pocket knife and widened the hole just enough to make the older (1933-34) Model 16 escutcheon fit. Icon_thumbdown

There are even two sets of screw holes visible - obviously one set for the proper escutcheon, and one set for the older, incorrect one.

Had this been done at the factory, the hole would have been hexagonal as were the original holes for the older Model 16 escutcheons.

--
Ron Ramirez
Ferdinand IN
#11

Good enough. Thanks. I'm always grateful to learn from other's vast base of knowledge.
#12

Scott, want to trade?

[Image: https://farm5.staticflickr.com/4465/3682...9712_k.jpg]109_0528 by Steve Davis, on Flickr

Steve

M R Radios   C M Tubes
#13

Hi Steve. I don't know. I'm afraid the top hole might show now. I will have to see how my other 144B escutcheon fits. I will let you know. Thanks.
#14

It probably wouldn't cover the extra hole. It was just a thought.

Steve

M R Radios   C M Tubes
#15

Why not take the escutcheon off your other 144B and see how it fits on the set with the older escutcheon? Then you will know whether it covers the hole, or not. Just a thought.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
Late last night a guy reached out in response to my posting on the Antique Radio Forum and suggested I contact Trust Aut...jrblasde — 11:01 AM
Philco 630csx power cord
Have you opened up that plug? It may be that the third wire is connected to that brass stud on the side of the plug and ...Arran — 02:57 AM
Model 27-84 BUZZ?Humm?
I would have to look at the schematic but it's not uncommon in 1930s AC radios to have the negative of one filter cap co...Arran — 02:46 AM
Model 27-84 BUZZ?Humm?
Hello Bruce, First all do mean a 37-84b ? Did you take any before and after pictures ? is it a buzz like when you touch...radiorich — 01:59 AM
B&K 1077B no video - problem solved
Hello Tim, Yes, I even check all of my replacement parts when I install them and I too had a capacitor go bad not long a...radiorich — 01:54 AM
B&K 1077B no video
I got back into it tonight. Problem found and resolved! Sometimes it helps to take a break and think things over. It was...TV MAN — 12:40 AM
6TPZ and 5TPO Radio Help
Thank you. I have to take a break from it for about a week. I'll have to do some thinking. I was toying with the idea ...R3Sons — 12:21 AM
Model 27-84 BUZZ?Humm?
Drowning in a overloud buzz/Humm. Have already changed filter caps,bakelite blocks( caps),out of speck resistors,checked...Bruce — 12:17 AM
Philco 630csx power cord
Hello Mike Here is the Link to the company the place is called Grand Brass lamp parts . I buy all my Lamp parts plus ...radiorich — 12:00 AM
Philco 40-120C Filament Wiring
Is the tube in your radio actually 35Z3 or 35Y4, or something else?morzh — 10:55 PM

[-]
Who's Online
There are currently 2733 online users. [Complete List]
» 2 Member(s) | 2731 Guest(s)
AvatarAvatar

>