Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 650 K-17 Speaker Transformer
#1

Hello Everyone,
I am having issues with a K-17 speaker. The output transformer was bad and I need to replace it. I'm having trouble crossing the 32-7078 transformer. I bought a Hammonds 125D universal push-pull, but and not sure how to wire it up. Anybody have experience with this and can point me in the right direction?

Thank You in advance.

Matt
#2

You have 10,000 kOhm to 1.11 Ohm transformer, which means you have the ratio of 95 of I:II windings. The impedance at 1.5 ohms should be 13,636 so the closest you get is by connecting your speaker between 3 and 4 of the secondary.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Hmmmm
The push/pull triode connected 42's w/fixed bias p to p load is 6K sez my '40 RCA tube manual and spec on the original transformer is 5.9K. With that in mind I would go w/ 1 and 3. Rca sez it will make abt 10watts @ 2% distortion. Wired as penodes they will abt twice the audio power but almost triple the distortion.
YMMV

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

I think you are right. I didn't look much at the output stage, it seems to be direct-biased triode connection (cathode biased triode is still 10K) which is 6K.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

>I think you are right.
I try!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
91H Code 126 Restore
Thanks Arran, I'm convinced the power cord is good but have a nice repro plug for it. Would it be prudent to add a fus...RealRider — 07:28 PM
91H Code 126 Restore
As I was studying this schematic I was wondering what does this dotted line means?  I haven't traced it out yet. An o...RealRider — 07:22 PM
91H Code 126 Restore
When it comes to the cloth covered power cords, if they are not frayed, and are flexible, and if I can bend one without ...Arran — 06:21 PM
An attempt to remove the Field Coil from a G speaker
Could be. The central cylinder is OK, but the sides are...well. What's done is done. I wonder if some standard bobbine w...morzh — 06:02 PM
An attempt to remove the Field Coil from a G speaker
Mike; As I was saying it doesn't look like they used much of a bobbin for the field coil, not like a Magnavox one wou...Arran — 05:49 PM
Atwater-Kent 84, restoration.
This AK84 was bought, I think, last fall. For a whopping $100. It has been, according to the seller, restored. As I go ...morzh — 05:48 PM
Philco model 60
Plus I forgot that I have a spare complete Philco FC speaker, that would work perfectly, now that I don’t need it. Got i...Radios1340 — 05:36 PM
Philco model 60
Duh! I guess I can’t read an ohm meter today. I took the oscillator coil out and will take some readings tomorrow.Radios1340 — 05:30 PM
An attempt to remove the Field Coil from a G speaker
Well, I killed the coil. Tried to get to the end of that oxidated spot, but while holding the coil in hand, i let it sl...morzh — 05:27 PM
91H Code 126 Restore
It does not require taking apart. Find an opening, any gap that would lead inside, where the resistive element and the ...morzh — 04:59 PM

[-]
Who's Online
There are currently 4865 online users. [Complete List]
» 2 Member(s) | 4863 Guest(s)
AvatarAvatar

>