1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
RCA 811K question
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#1

03-23-2019, 08:56 PM
Hello fellas,
Have a question concerning my 811k .
Swapping transformers and seem to have lost my wire ID tags on a couple wires coming out of the transformer.
These are the 2 largest dia wires.
One goes to pin 2 on the 6J7 tube and the other goes to pin 7 on the 6J7 tube.
Any chance these wires could be swapped or are they specific to these connections?
Apparently my id tags came off as I removed the transformer from the chassis.
Any help would be much appreciated.
murf
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

03-23-2019, 09:29 PM
As long as you have abt 6vac across the two wires your good. Phase relationship doesn't matter.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
murf
Senior Member
****
Posts: 669
Threads: 145
Joined: Jun 2011
City: Elko,MN.
#3

03-24-2019, 08:23 AM
Hi Terry,
Just want to make sure I solder them in right the first time.
Sounds like it can go either way.
Thanks to all,
murf
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#4

03-24-2019, 09:50 PM
All,

The Philco 39-6 posts have been split off into a thread of their own.

https://www.philcoradio.com/phorum/showt...?tid=19786
--
Ron Ramirez
Ferdinand IN
Find
Jake Blake
Banned
Posts: 816
Threads: 25
Joined: Mar 2014
City: Louisville, KY
#5

03-24-2019, 10:20 PM
I was wondering if that was gonna happen.    Sorry.   Icon_redface
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 630csx power cord
Have you opened up that plug? It may be that the third wire is connected to that brass stud on the side of the plug and ...Arran — 02:57 AM
Model 27-84 BUZZ?Humm?
I would have to look at the schematic but it's not uncommon in 1930s AC radios to have the negative of one filter cap co...Arran — 02:46 AM
Model 27-84 BUZZ?Humm?
Hello Bruce, First all do mean a 37-84b ? Did you take any before and after pictures ? is it a buzz like when you touch...radiorich — 01:59 AM
B&K 1077B no video - problem solved
Hello Tim, Yes, I even check all of my replacement parts when I install them and I too had a capacitor go bad not long a...radiorich — 01:54 AM
B&K 1077B no video
I got back into it tonight. Problem found and resolved! Sometimes it helps to take a break and think things over. It was...TV MAN — 12:40 AM
6TPZ and 5TPO Radio Help
Thank you. I have to take a break from it for about a week. I'll have to do some thinking. I was toying with the idea ...R3Sons — 12:21 AM
Model 27-84 BUZZ?Humm?
Drowning in a overloud buzz/Humm. Have already changed filter caps,bakelite blocks( caps),out of speck resistors,checked...Bruce — 12:17 AM
Philco 630csx power cord
Hello Mike Here is the Link to the company the place is called Grand Brass lamp parts . I buy all my Lamp parts plus ...radiorich — 12:00 AM
Philco 40-120C Filament Wiring
Is the tube in your radio actually 35Z3 or 35Y4, or something else?morzh — 10:55 PM
Philco 630csx power cord
Second Rich's opinion. Run a separate antenna wire. Use a separate plug. Rich Where did you get this wire? Se...morzh — 10:51 PM

[-]
Who's Online
There are currently 1526 online users. [Complete List]
» 3 Member(s) | 1523 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)