1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
philco model D-664
retired2020
Junior Member
**
Posts: 12
Threads: 4
Joined: Feb 2021
City: middletown State, Province, Country: Delaware
#1

01-21-2024, 05:31 PM
restoring this portable radio D664 

Before restoration turned it on and got lots of noise but no stations. Assumed eletrolytics  were bad as well as old selenium rectifier since it only put  out 107 volts not 125  as shown on schemo . Also  replaced paper capacitors, and c4 , 3 and 7 . All tubes tested and Okay. tested all resisters and okay.  Same issue and voltage at diode not any higher. While  all tubes were good at startup noticed that  IU4 was glowing brightly , so tested  all tubes IU4 and IU5  are now NG  . Before  replacing tubes powered up without them .Only got 9 V dc at Diode  output but  -151 V DC at pin 1 on IU4 .Also  noticed same voltage on the socket tab that connects to the IU4  heat shield . Any suggestions helpful


Attached Files
.pdf d 664 schemo.pdf Size: 947.44 KB  Downloads: 122
Find
klondike98
Phorum Moderator
******
Posts: 5,123
Threads: 271
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

01-21-2024, 06:37 PM
Moved this thread over to the Electronic Restoration section.

Just a thought… double check your cap and other replacement wiring. I’ve mis-wired more than once and had to back track to sort it out.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM
Var resistor id
Its a Sylvania 400 oscilloscope. here is a clip of r-100. Would be nice to know the current required. Not listed in part...Martinj — 02:10 PM
The list of my radio & TV collection!
Thanks Richard. I hope you enjoy it. Here I have created an English section on the history of radio with videos in Engl...RadioSvit — 10:23 AM
The list of my radio & TV collection!
Hello RadioSvit, first all happy new year ! I will watch your new videos this week. Sincerely Richardradiorich — 09:19 AM

[-]
Who's Online
There are currently 3771 online users. [Complete List]
» 1 Member(s) | 3770 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration