Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Latest acquisition
#1

Thanks to my friend Ed in Ohio, I now have this neat addition to the collection:

[Image: http://philcoradio.com/gallery2/images/1...age_00.jpg]

A Model 43B, from June 1932. Philco's first complete, all-in-one all-wave receiver.

Anyone else find anything new/neat/unusual in the Philco line lately?

--
Ron Ramirez
Ferdinand IN
#2

Oooo! Beauty!
#3

Hi All,
Nice radio Ron. A fine catch! At the end of July I picked up a Philco 90 for $65.00. A lot was wrong upon inspection. The (tiger stripe)? veneer is mostly gone but the rest is o.k. The primary on the first detector coil was open. The speaker field coil was open also. The filter choke along with the output transformer were open too. The tunning cap had to be cleaned also.The choke and output transformer were ordered from Radio Daze along with a #47 tube. The detector coil break was on the first loop. The speaker field I wound with #36 guage wire. I only had a little over a half pound which gave me 2600 ohms so I put a 10W 500 ohm resistor in series. You talk about tough getting the speaker core out! Wow. I drilled and tapped a 1/4 bolt to hold it in. After a rebuild of the cap blocks, a few resistors and electrolytics it plays great!!
Last friday the wife and I went back to the same place and there sat another 90! I got this one for $43.00. It rained here all day Saturday so I tore into this one. Not much wrong but a lot of recapping and resistors. hopefully I can power up tomorrow. The chassis has a lot of rust though. Will have to start cleaning after I get it playing.

Terry
#4

Hmph! Some people have all the luck! Icon_biggrin

Great buys on your 90 sets. Now would you consider letting go of the rusty one? Icon_lol Just kidding of course. Congrats!

--
Ron Ramirez
Ferdinand IN
#5

Ron,
Thank you. I am kind of proud of them. By the way #2 is up and running Icon_lol

Terry
#6

Now, another acquisition:

This set came from the Olney auction this past Sunday.

[Image: http://www.philcoradio.com/images/phorum...ff/112.jpg]

It is a 112 Bel Geddes lowboy, has some minor veneer issues, and the knobs - well, two of the knobs are 1937-40 Philco, the tuning knob is from an RCA, and the off-on knob is missing. Cloth is not original. The chassis is the later version with push-pull Type 47 outputs (one of the Type 47 tubes is missing).

The price: $20. No-one bid against me. Oddly enough, other consoles brought more money than this one did.

A friend of mine says I "stole" this at the $20 price. What say you guys?

--
Ron Ramirez
Ferdinand IN
#7

Dang...!!! Very nice catch. Icon_eek
#8

Ron,
Your lucky I wasnt at that auction. Looks like its "philco season".
Nice finds!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
6TPZ and 5TPO Radio Help
Welcome to the Phorum, R3Sons! I have very limited experience with car radios other than installing custom radios back ...GarySP — 01:08 PM
462ron
OK, I need to rename this thread to say..Eico 368 TV/FM Sweep Generator instead of the current title..Heathkit Sweep Gen...462ron — 12:49 PM
6TPZ and 5TPO Radio Help
Hello, I have a Philco (Ford) 6TPZ and a 5TPO radio.  I replaced the electrolytic capacitors in both.  I have the SAMS m...R3Sons — 12:29 PM
The list of my radio & TV collection!
Hello Peter, Thank you for posting that !! Sincerely Richardradiorich — 09:40 AM
Eico 232 VTVM Schematic
It's a microwave antenna. ?;-p?. I substituted 1N4002s off the 6.3 vac winding for the 1.5 volt battery. Uniprobe is the...RodB — 05:50 PM
Eico 232 VTVM Schematic
Try BAMA for a schematic. Looks like a replacement power source for the D battery has been installed. The tube may be...Chas — 04:51 PM
Eico 232 VTVM Schematic
Is that a battery holder?morzh — 04:43 PM
Eico 232 VTVM Schematic
A friend gave me this Eico 232 VTVM and I'm having trouble locating the schematic for it. This one seems to be a later v...RodB — 04:17 PM
Var resistor id
Considering what it is in series with, I doubt there should be any power requirements. Of course, we should know wher...morzh — 03:23 PM
Var resistor id
Trim pot, about 1/2 watt part of focus divider. As stated 2k ohms. This appears to be a rusty chassis, resolder all ...Chas — 03:19 PM

[-]
Who's Online
There are currently 8640 online users. [Complete List]
» 3 Member(s) | 8637 Guest(s)
AvatarAvatarAvatar

>